eagletone.com
eagletone.com
• Shields, lenses or ultraviolet screens shall be changed if they have become visibly damaged
to such an extent that their effectiveness is impaired, for example by cracks or deep
scratches.
• The lamp shall be changed if it has become damaged or thermally deformed.
PROCEDURE:
- Remove the screw on the front, holding the glass pane
- Carefully remove the glass pane by making a counter-clockwise movement, making sure it
doesn’t get damaged
- Remove the old lamp carefully
- Place the new lamp
- Close the glass pane by making a clockwise movement
- Fasten the screw
CAUTION
• Do not operate this device with open cover!
• The glass pane has to be replaced when it is damaged!
• The lamp has to be replaced when it is damaged or deformed!
• Only install the lamp with the device unplugged from the mains!
FUSE REPLACEMENT
• Disconnect the power cord before replacing a fuse and always replace with the same type of
fuse.
• With your hands, unscrew the fuse holder from its housing, remove the damaged fuse from
its holder and replace with exactly the same type of fuse. Screw the fuse holder back in its
place and reconnect power.
MOUNTING
• The installation must always be secured with a secondary safety attachment, e.g. an
appropriate safety cable.
• Never stand directly below the device when mounting, removing or servicing the device.
• The stroboscope should be installed outside areas where persons may reach it, walk by or
be seated.
• Overhead mounting requires extensive experience, including amongst others calculating
working load limits, installation material being used, and periodic safety inspection of all
installation material and the device. If you lack these qualifications, do not attempt the
installation yourself. Improper installation can result in bodily injury.
• Before mounting make sure that the installation area can hold a minimum point load of 10
times the device’s weight.
CAUTION: WHEN INSTALLING THE DEVICE, MAKE SURE THERE IS NO HIGHLY
INFLAMMABLE MATERIAL WITHIN A DISTANCE OF MIN. 1M!
SAFETY INSTRUCTIONS
• Please keep this User’s Manual for future reference. If you sell the unit to another user, be
sure that he also receives this instruction booklet.
• Unpack and check the unit carefully that it has not been damaged during transport before
using the unit.
• Before operating, ensure that the voltage and frequency of power supply match the power
requirements of the unit.
• In the event of serious operating problem, stop using the unit immediately.
• Never operate the stroboscope without glass pane or with a broken glass pane.
• Never try to repair the unit by yourself. Repair carried out by unskilled people can lead to
damage or malfunction. Please contact the nearest authorized technical assistance center
and always use the same type of spare parts.
• Do not touch any wires during operation as high voltage might be causing electric shock.
• To prevent or reduce the risk of electrical shock or fire, do not expose this unit to rain or any
moisture.
• If this unit will not be used for a long period of time, disconnect if from power supply.
• Prior to moving or handling the light effect, the unit MUST be SWITCHED OFF and cool down
for at least 10 minutes. The lamps are not covered by the warranty.
• Never look directly into the light source as sensitive persons may suffer an epileptic shock.
• During initial start-up, some smoke or smell may arise. This is normal and should decrease
gradually.
INSTALLATION
GENERAL GUIDELINE
• When choosing the installation spot, please make sure that the device is not exposed to
extreme heat, moisture or dust. The minimum distance between light-output from the
projector and the illuminated surface must be more than 0.5 meter.
• Operate the device only after having familiarized yourself with its functions. Do not permit
operation by persons not qualified for operating the device. Most damages are the result of
unprofessional operation.
• Please use the original packaging if the device is to be transported.
• For safety reasons, please be aware that all modifications on the device are forbidden.
Furthermore, any other operation may lead to short-circuit, burns, electric shock, lamp
explosion, crash, etc. If this device will be operated in any way different to the one described
in this manual, the product may suffer damages and the guarantee becomes void.
INSTALLING OR REPLACING THE LAMPS
• Before replacing the lamps let the lamps cool down, because during operation, the lamps
can reach temperatures of up to 700°C. Wait at least 10 minutes after use before opening
the housing.
• During the installation of the lamp do not touch the glass bulb bare handed. Always use a
cloth to handle the lamp during insertion and removal.
• Do not install lamps with a higher wattage. They generate higher temperatures than for
which the device was designed for.
• For the installation, you need a 1500W strobe lamp.
Eagletone Big Strob 1500W
Manuel d’utilisateur
Manuel d’utilisateur
Eagletone Big Strob 1500W
