Eagle EI-4000 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 33

Eagle EI-4000 Скачать руководство пользователя страница 9

SETUP MENU/CONFIGURATION

To enter configuration, press the MNU pushbutton and then press the CFG pushbutton. If the
password is enabled, enter the correct password and then the first parameter (P001) is
displayed. The password screen is explained later in this manual.

Each screen (except for P010) has pushbutton functions are as
follows:

NXT

– Selects the next parameter.

LAST

– Selects the last parameter.

ADJ

– Make an adjustment to the selected parameter.

ESC

– Return to the

The top line of the display shows the parameter number (Pxxx), parameter name
(abbreviated), and the parameter value.

When the ADJ (adjust) pushbutton is pressed, the user can make
adjustments to the parameter value using the UP or DOWN
pushbuttons. Press the ENT (enter) pushbutton when the value
displayed is correct.

P001 Operation (1 – 5)

This selects the operating mode for the meter. See the “operating
modes” section of this manual for a detailed description of each
one.

P010 lb/kg (display only)

This displays the engineering unit, lb or kg, selected by S1-3. The
user can change the units DIP switch at any time; all values that
were entered in pounds are automatically converted to kilograms
and vice versa.

P020 Used display enable/disable (ON/OFF)

If set to on, the used display is available to be selected via the
select pushbutton in the main weight screens.

SCALE PARAMETERS

P100 through P400 set needed parameters for the attached scale bases. If a scale base is
set to OFF, this applies to channels 2, 3 and 4; all of its parameters are hidden except for the
scale selection.

P100-P199

Scale 1 parameters

P200-P299

Scale 2 parameters

P300-P399

Scale 3 parameters (EI-2000-EXP must be installed)

P400-P499

Scale 4 parameters (EI-2000-EXP must be installed)

Pxxx name value
NXT LAST ADJ ESC

Pxxx name value
UP DOWN ENT

P001 OPERATION 3
NXT LAST ADJ ESC

P010 UNITS lb
NXT LAST ESC

P020 USED OFF
NXT LAST ADJ ESC

«
...
7
8
9
10
11
...
»

Содержание EI-4000


































Отзывы:

Нет отзывов