Eagle EI-4000 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 33

Eagle EI-4000 Скачать руководство пользователя страница 4

POUND (lb) AND KILOGRAM (kg) UNITS OPERATION

The EI-4000 meter may operate using lb or kg units. DIP switch
S1-3 selects the desired unit. If one wishes to switch to the other
unit, simply flip the switch to the opposite setting; no recalibration
is necessary. It is necessary to select the proper S1-3 switch
setting so the unit selection works properly (i.e., do not calibrate the scale in kg if the S1-3
switch is set to lbs). Also, all parameters that were set using the previous units are converted
to the equivalent value of the newly selected unit.

OPERATING MODES

1:GR 136.0 kg
SEL SCL MNU

The EI-4000 meter has five operating modes to simplify user interactions with the meter.
Configuration parameter P001 selects which operating mode, 1 thru 5, is enabled for all scale
channels.

MODE 1: FULLY MANUAL MODE

Typical application: drum scales, bin and hopper scales - Remaining, tare, & gross weights
are displayable.

1.

An empty scale should read zero. If it does not, press the ZRO (ZERO)
pushbutton. If the ZRO pushbutton is not displayed, access the calibration
mode to zero the scale.

2.

Place container on the scale.

3.

Press the SELECT pushbutton to go to the tare weight.

4.

If necessary, adjust the tare weight value via the arrow pushbuttons.

5.

Press the SELECT pushbutton to go to the remaining weight.

MODE 2: ADJUSTABLE REMAINING

Typical application: drum scales - Remaining & gross weights are displayable.

1.

An empty scale should read zero. If it does not, press the ZRO (ZERO)
pushbutton. If the ZRO pushbutton is not displayed, access the calibration
mode to zero the scale.

2.

Place container with product on the scale.

3.

Instrument will show the REMAINING weight and will flash the REM text.

4.

Use the UP and DOWN arrow pushbuttons to adjust the remaining weight
displayed.

5.

Press the ENT pushbutton after making any adjustments; the user will no longer
be able to adjust the remaining weight.

If you need to adjust the REMAINING weight again, press and hold PB3 for 3 seconds, the
REM text will start to flash and the remaining weight will now be adjustable. Press the ENT
pushbutton when finished.

«
...
2
3
4
5
6
...
»

Содержание EI-4000


































Отзывы:

Нет отзывов