background image

  TROUBLESHOOTING

  

WARRANTY NOTICE

This service jack is covered under a 1-year limited warranty when used as recommended. Only those items listed with a Part # are available 
for purchase. For assistance with the operation or the availability of replacement parts. Please a have available a copy of your receipt, the 
model number of the product, serial number regarding your question.

Not all equipment components are available for replacement; illustrations provided are a convenient reference of location and position in the 
assembly sequence.

The manufacturer reserves the rights to make design changes and or improvements to product lines and manuals without notice.

JACK WILL NOT 

LIFT LOAD

×

×

×

×

×

×

×
×

×

×

×

×

×

×

×

JACK WILL NOT 

HOLD LOAD

JACK WILL

NOT LOWER

POOR JACK

LIFTING

WILL NOT LIFT TO

FULL EXTENSION

CAUSES AND SOLUTIONS

Release valve is not completely closed

(Turn handle clockwise)

ReWeight Capacity Exceeded

Air is in the hydraulics.

Purge air from system

Low oil level. Add oil as required.

Jack is binding or foreign obstruction

Power unit malfunctioning.

Replace the power unit

Drain excessive oil.

Lubricate moving parts

Part List

Item No.

Description

Q'TY

Item No.

Description

Q'TY

1

Front Wheel

2

24

Idler Wheel

1

2

Retainer Ring 20

4

25

Small Handle Socket

1

3

Washer 16

2

26

Washer 6

1

4

Nut M16

2

27

Nut M6x10

1

5

Real Wheel

2

28

Foot Pedal

1

6

Lift Arm Shaft

1

29

Spring

1

7

Retainer Ring 25

2

30

Rear Handle

1

8

Washer 10

4

31

Locating Pin

1

9

Bolt M10x25

4

32

Handle Sleeve

1

10

Bolt ST5.5x16

4

33

Front Handle

1

11

Washer 16W

2

34

Pump

1

12

Screw 16

2

35

Tension Spring

2

13

Washer 8

4

36

Pin 4x50

1

14

Nut M8x20

4

37

Link Member

1

15

Washer

2

38

Oil Cup M6

1

16

Washer 18

2

39

Bolt

2

17

Bolt

2

40

Long Connecting Rod

2

18

Shaft

2

41

Frame

1

19

Handle Socket

1

42

Retainer Ring 14

2

20

Cover Board

1

43

Lifting Arm

1

21

Roller Shaft

1

44

Saddle

1

22

Locating Screw

1

45

Screw

1

23

Washer12

1

46

Rubber Pad

1

www.eagleprojacks.net

Содержание E1525P










Отзывы: