background image

   

 

                Installation,  Operation  and  Parts  Manual 

EE-6435BWF 

                                                                                                                                                                                                                                                                                                                                                                 

 

1.3 Important safety notices   

1.3.1 Recommend for indoor use only. DO not expose the lift to rain, snow or excessive moisture.   

1.3.2 Only use this lift on a surface that is stable, level and dry and not slippery, and capable of sustaining the load. Do not install the lift on 

any asphalt surface.   

1.3.3 Read and understand all safety warnings before operating the lift. 

1.3.4 Do not leave the controls while the lift is still in motion. 

1.3.5 Keep hands and feet away from any moving parts. Keep feet clear of the lift when lowering.   

1.3.6 Only these properly trained personnel can operate the lift.   

1.3.7 Do not wear unfit clothes such as large clothes with flounces, tires, etc, which could be caught by moving parts of the lift. 

1.3.8 To prevent evitable incidents, surrounding areas of the lift must be tidy and with nothing unconcerned.   

1.3.9 The lift is simply designed to lift the entire body of vehicles, with its maximum weight within the lifting capacity. 

1.3.10 Always insure the safety locks are engaged before any attempt to work near or under the vehicle. Never remove safety related 

components from the lift. Do not use if safety related components are damaged or missing. 

1.3.11 Do not rock the vehicle while on the lift or remove any heavy component from vehicle that may cause excessive weight shift. 

1.3.12 Check at any time the parts of the lift to ensure the agility of moving parts and the performance of synchronization. Ensure regular 

maintenance and if anything abnormal occurs, stop using the lift immediately and contact our dealers for help. 

1.3.13 Lower the lift to its lowest position and do remember to cut off the power source when service finishes. 

1.3.14 Do not modify any parts of the lift without manufacturer’s advice. 

1.3.15 If the lift is going to be left unused for a long time, users are required to: 

a. Disconnect the power; 

b. Empty the oil tank;   

c. Lubricate the moving parts with hydraulic oil.   

WARNING

The warnings, cautions and instructions discussed in this instruction manual cannot cover all possible conditions and 

situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into 

this product, but must be supplied by the operator. 

Attention: For environment protection, please dispose the disused oil in a proper way. 

 

 

 

 

Содержание EE-6435BWF
























































Отзывы: