background image

5

4.Hardware installation

Your

module has been designed for the internal expansion

port of the

Zorro card from E3B. Connection with other

manufacturers' cards is not possible and can lead to damage of either
the

, the othermodule and / or yourAmiga.

Switch off yourAmiga before installation.
Remove the power supplyACcable.
Disconnect all external devices.
Avoid static charge.
Follow your computer manufaturer's installation
guide for expansion cards.

module

Zorro card

one holding plate with SUBD9 connector
one adaptor SUBD9 to RJ45
Philips style screw driver

NORWAY

NORWAY

NORWAY

HIGHWAY

HIGHWAY

4.1. Safety recommandations

4.2. List of required material

Please follow these recommandations

for your own safety:

>
>
>
>
>

1
1
1
1
1

NORWAY

8

5. First steps

5.1. A first test

5.2. Troubleshooting the expansion port

5.3. Troubleshooting the network

Do

connect a network cable to the

. After you have

completed the hardware installation and closed your Amiga's housing
you can switch on your computer.
Should you recognize any unusual behaviour of your Amiga, please
switch it off immediately. Please consult chapter 5.2 and 5.3 for trouble
shooting instructions.

After booting your Amiga please read the software installation manual
in the AmigaGuide file "Software Manual" on the disk enclosed in your
package You can also use the program

(available on our

website) to check the

module and display hardware and

firmware revision as well as the NIC MAC address..

Installation is quite easy: check if the directory
already exists. If not, create it by

and

copy the file

into this directory.

Should problems occur during the first test, please carefully check if:

the

has beenmounted in the right orientation ?

there are there any left-over pins at the expansion port ?
any cables have been removed or damaged during installation ?

Please check carefully if:

you are using the right cable type (straightforward / crossover) ?
the hubport you are using is activated ?
your network support 10MBit connections ?

Your status LEDs should show short pulses on both

and

LEDs,

no

and a statically activated

LED.

not

NORWAY

NORWAY

NORWAY

nwtest

devs:Networks

"makedir devs:Networks"

norway.device

TX

RX

COL

LNK

1
1
1

1
1
1

NORWAY

Содержание NORWAY









Отзывы: