E2S APPELLO A121AX Скачать руководство пользователя страница 9

Страница: 9 / 10

European Safety Systems Ltd.

Impress House, Mansell Road, Acton, London W3 7QH

[email protected]

Tel: +44 (0)208 743 8880

www.e2s.com

Fax: +44 (0)208 740 4200

Document No. D165-00-001-IS_Issue_3 16-11-22

Sheet 9 of 10

Quick Ref - Synchronising Two Sounders (All stages)

Connect Synch cable to
Master and Slave PCB

Set 1 off Units as Master
and 1 off Unit as Slave
Set jumper to SY on

Set jumper MA on Master
unit to master position
(on)

Set jumper MA on Slave
unit to slave position (off)

Position of S2 switch
does not affect synch
operation.

Switch on power onto the
Master unit first

Then switch power onto
the Slave unit

Master Unit

Slave Unit

Press action button on the
Master Unit:
Synchronisation will begin
(Duration 13 Minutes)

Master Unit

Slave Unit

- - - - Synchronisation
complete

Switch off Power to units

Master Unit

Slave Unit

Reset on both units
jumper SY to off

Set jumper MA on both
units to Master position
(on)

Содержание APPELLO A121AX











Результаты поиска

Содержание APPELLO A121AX

Отзывы:

Похожие инструкции для APPELLO A121AX

Бренды по названию

Популярные бренды

E2S APPELLO A121AX, Инструкция по эксплуатации

Результаты поиска

Содержание APPELLO A121AX

Отзывы:

Похожие инструкции для APPELLO A121AX

Бренды по названию

Популярные бренды