background image

Page 12 

 
When the brake is fully applied there should be a 
minimum clearance of ½” of clearance between 

the lever and the handle bar grip. If this clearance 
is less that ½” your brakes should be adjusted 

 

After riding your unit, be sure to clean any build 
up of mud, sand and dirt from the brake cable 
and adjuster to prevent rust and corrosion that 
could cause cable failure. 

 

Drive Chain 

The drive chain will stretch with use and will 
require periodic adjustments. To check the chain 
tension, remove the chain guard and measure the 
slack. 

 
 

The amount of slack in the chain should not 
exceed 10-20mm or ¼” - ½”.   

 
Inspect the drive and axle sprockets for worn, 
damaged or broken teeth. Replace as needed. 

Inspect the chain links for damaged, worn or loose 
rivets. Repair or replace as needed. 

 

Chain Slack Adjustment 

Loosen the axle position lock bolt slightly and turn 
the chain adjuster nut to take up the excess slack in 
the chain.  Once the chain has been adjusted to the 
proper tension retighten the axle position locking bolt. 

 

The chain should be kept well lubricated to prevent 
excess wear and premature failure. We recommend 
that you lubricate the chain every 15 hours of 
operation, or more frequently if needed, with a high 
quality chain lubricant. 

 

Throttle Lever 

 

 

The throttle lever is located beside the right-
handlebar grip and is operated by using the right-
hand thumb. The lever is spring loaded and will 
return to the idle position when you remove your 
thumb from the lever. To accelerate the unit, simply 
press the lever forward to open the throttle slide in 
the carburetor. To slow the unit, reduce the pressure 
on the lever or remove your thumb and the throttle 
will return to the idle position automatically. 
 

  

Adjusting the throttle

  

The cable should be adjusted to allow for 

” free 

travel before the throttle engages the carburetor 
throttle slide. To adjust the cable’s free travel, loosen 
the locking nut of the cable adjuster, and turn the 
adjuster wheel until there is 

” free travel in the 

Содержание Viper 40E (RXL-40E)

























Отзывы: