background image

 

 

3.BEFORE RIDING 

4.SAFE RIDING 

 

3.BEFORE RIDING

 

This manual describes the correct usage of this motorcycle including safety riding, simple inspection 

methods and so on. 

For a more comfortable and safety riding, please read this manual carefully. 

For your benefit, please ask your E-TON dealer the operating manual and carefully read the following: 

y

  Correct use of the

 

motorcycle.

 

 

y

  Pre-delivery inspection and maintenance. 

 

 

Thank you very much for your patronage 

In order to maximize your motorcycle’s performance, a periodical inspection and maintenance 

should be completely carried out. 

We recommend that after riding your new motorcycle for the first 300 kilometers, you should take 

your motorcycle to the original dealer for an initial inspection, and to have your motorcycle inspected 

periodically every 1000 kilometers thereafter. 

 

 

y

  In case the motorcycle’s specifications and construction are modified and different from the photos 

and diagrams on the owner’s manual / catalogues, the specifications and construction of the actual 

motorcycle shall prevail. 

4. SAFE RIDING

 

It is very important to be relaxed and clothe properly when driving, observe traffic regulations, do not rush, 

always drive carefully and relaxed. 

Usually, most people would ride their newly bought motorcycle very carefully, but after they became familiar 

with their motorcycles, they tended to become reckless which may result in an accident. 

 

To remind you:

 

y

  Please wear a safety helmet, and properly tighten the chin belt when riding a motorcycle.   

y

  Clothes with open or loose cuffs may be blown by wind and cause the cuffs to get caught on the 

steering handle and thus affects riding safety.   

y

  So, put on clothes with tight sleeves. 

y

  Hold the steering handle by both hands when riding.    Never ride with only one hand. 

y

  Observe the speed limit. 

y

  Wear suitable low-heel shoes.

 

y

 

Perform periodical maintenance and inspection in accordance with the schedule.

 

 

 

 WARNING!! 

y

  To avoid getting burned by exhaust pipe when taking a passenger.    Make sure your passenger has 

put his/her feet on the pedals. 

y

  After running, the exhaust pipe is very hot, be careful not to get burned when conducting an 

inspection or maintenance. 

y

  After running, the exhaust pipe is very hot, select a suitable location to park your motorcycle to avoid 

others getting burned by the exhaust pipe. 

 

 CAUTION: 

Modified motorcycle will affect its structure or performance, and cause poor engine operation or 

exhaust noise, which will result in shortening the motorcycle’s service life. 

Besides, modification is illegal and does not conform to the original design and specifications. 

A modified motorcycle will not be covered by warranty; therefore, do not modify your motorcycle at 

will. 

 

 

Copyright ©2008-2009 ETON America, all rights reserved.

Содержание AV05W9-A
































Отзывы: