E.T. Systems UMPETHA Скачать руководство пользователя страница 28

Страница: 28 / 30

UMPETHA 082009/072010.014

Beeps

Gate status

Program

Jumper

Action

Response

Motor

Condition

Solution

Table ref:

5 x Rapid

beeps

Full closed

Off

Momentary

BT or Ped

input

None

Holiday lock-

out active

Toggle off

pg 26

Continuous

rapid beeps

Gate

anywhere

None

Holiday lock-

out active

Toggle off

pg 26

5 x Rapid

beeps

Gate

anywhere

but closed

Off

Momentary

BT or Ped

input

None

Auto-close

override/party

mode active

Toggle off

pg 27

1 x 5sec beep

(long beep)

Opens 1m

and remains

there.

Off

Momentary

BT or Ped

input

None

limit failure

check magnet on

gate and limit switch

pg 20

2 x Rapid

beeps

Gate

anywhere

Off or On

Momentary

BT or Ped

input

Attempts to run

Battery flat or

faulty

Allow recharge and

check for Aux devices

overload. If problem

persists after ±8 hours

charging, replace

battery

3 x 1sec. Beeps

Gate closed

Off

Momentary

Ped

Gate opens

partially

Pedestrian

function

activated

pg 27

2 x 2sec. Beeps

Gate

stopped

Off

Momentary

Gate runs

Household

mains failure

Restore power supply

1 x 5sec beep

(long beep)

Gate

stopped

Off

Any input

triggered

None

Multiple

collision lock-

out

Check gate closing

resistance

pg 20

20 x 1sec.

Beeps.

Gate

stopped

Off or On

First BT input

after a reset

or Set

button in

runtime set

None

No motor

movement

detected or

beam input is

activated

before the

closed limit is

seen.

Check beam circuit or

setting. Check gate

resistance. Check

motor and battery

wiring/looms.

pg 19, 20

&14

Status LED overview

Off

Gate closed

Slow flash

Gate is running or w aiting for auto-close time to time out

Gate is open

Rapid Flash

Gate is obstructed or has exceeded max run time.

Courtesy light out

Available in all modes.

The courtesy light output will activ ate on any opening trigger (BT or Pedestrian). The light output will remain

on until three minutes after the gate has re-closed.

Содержание UMPETHA































Результаты поиска

Содержание UMPETHA

Отзывы:

Бренды по названию

Популярные бренды

E.T. Systems UMPETHA, Инструкции по установке

Результаты поиска

Содержание UMPETHA

Отзывы:

Бренды по названию

Популярные бренды