manualshive.com logo in svg

E.T. Systems UMPETHA, Инструкции по установке

Поделиться
Скачать
E.T. Systems UMPETHA Скачать руководство пользователя страница 15

UMPETHA 082009/072010.014 

 

15

 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Runtime Setup

Action 

Response

Gate starts opening

Gate stops and closes

1 beep

Remove program jumper or continue to next feature 

Gate stops, 1 beep

Gate will now close correctly

Gate starts opening

Gate stops and closes

Continuous beep off

The run- time routine must be completed before attempting to continue with any other routine! The closed 

limit actuator must be installed correctly before starting this routine!

1.

Gate midway and engaged.

2.

Program jumper on 

2 beeps

3.

All dip-switches off.

4.

Press and release Set button 

Gate must close.

 

If gate opens first 

press and release set button then 

see A below!

             

5.

At closed limit

6.

Press and release Set button at 

required full open position (± 25mm short 

of physical stopper)

7.

At closed position

*** 

Changing gate direction if it opens first above.

A) 

On pressing and releasing the set 

button while gate was opening first

B) 

Dip-switch 3 on

C) 

Press and release Set button

D) 

At closed limit

E)

 Press and release Set button at 

required full open position (± 25mm 

short of physical stopper)

F) 

At closed position

1 beep, pause, continuous 

beep.

G) 

Dip-switch 3 off

Содержание UMPETHA































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды