e-survey E800 Скачать руководство пользователя страница 14

 

 

E800 User Manual 

 

Web

www.esurvey-gnss.com

                                     Email: [email protected] 

 

3.5

 

Sensor 

The 

new E100

 supports E-bubble and MEMS. It is determined by the activation code 

for which sensor is activated. Please note only one of the sensors can be activated. If 
you  purchase  E-bubble  code,  you  can  update  to  MEMS  later  by  contacting  with 
salesman. 

3.5.1

 

E-bubble Calibration 

When  e-bubble is activated on E100. To calibrate the e-bubble, put the device on flat 
table  or  pole  (ensure  the  bubble  on  the  pole  is  normal  before  calibration,  then 
centering the pole bubble). In SurPad4.0 software, 

connect device and click “Device” 

-

> “Device Settings”, open “E

-

Bubble” function. Then, go to “Device” 

-

> “Calibrate 

Sensor”, click “Calibrate” t

o calibrate the e-bubble. 

To use tilt survey function, go to “Survey” 

-

> “Point Survey” page, select “Tilt Point”. 

Then click survey button to start data collection. After collect three points on the same 
location, the software will calculate a final result. 

 

 

3.5.2

 

MEMS Tilt Survey 

When   MEMS  sensor  is  activated  on  E100. To  calibrate  the  MEMS sensor,  receiver 
must be in Fixed solution. In SurPad4.0 software, 

connect device and click “Device” 

-> 

“Device  Settings”,  enable  “Pole  Tilt  Correction”  function.  Then,  go  to  “Survey” 

-> 

“Point Survey” page. The software will guide user to calibrate the sensor.

 

 

Input the correct pole height  

 

Draw circle on the ground using the pole 

 

Follow the guide and shake the pole back and forth for around 5-10 seconds or 
walk in strai

ght line around 10 meters until it shows “Ready”

 

Содержание E800






















Отзывы: