UHD 18
manual
SAFETY INSTRUCTION
Read this manual carefully and completely. Keep it for future reference. This product is not intended to be used by children or persons with limited mental or motoric capabilities.The product mut be secured
against such use. The use of this product is only allowed in the way described in the section „description and function“. Do not expose the product to heat or moisture and do not put any objects on top of the
product. The device can get warm during operation.
Not attending to the safety instructions may result in injury and/or property damage.
DESCRIPTION AND FUNCTION
This splitter allows the concurrent distribution of UHD signals to up to eight display devices (e.g. TV, Beamer).
INSTALLATION
1. Make sure that all devices are switched off before you start the installation of the product.
2. Connect the signal source to the HDMI input of the splitter.
3. Connect the HDMI outputs to the display devices (Out1 - Out8)
4. Connect the included AC/DC adapter to the UHD 18.
5. Turn on all connected devices.
6. When not in use, remove the splitter from the main circuit.
HANDLING
The splitter allows cable lengths aup to 20m. We recommend cables from e+p HDMV-series for connection.
1. When the AC/DC adapter is connected the LED „Power“ is on.
2. When the signal source is switched on the LED „In“ is on.
3. Upon also the display devices are switched on the retrospective LEDs Output1 to Output8 are on.
Troubleshooting
a) Press the „Reset“ button at the splitter.
b) Check all cable connections.
c) Check the setup at the connected devices.
SPECIFICATIONS
input and outputs:
HDMI sockets
resolutions:
480i/p, 576i/p, 720p, 1080i/p, 2160i/p (=4Kx2K at 60Hz)
transfer rate:
max. 18GBit/s
measurements (splitter):
123x51x20mm
operating temperature:
0°C - 45°C
AC/DC adapter:
5V/3A
power consumption:
max. 10W
SETUP, MAINTENANCE AND CARE
The product is for use in dry, humid indoor rooms only. Protect the product against moisture, direct sunlight or high temperatures. If the product is not in use, disconnect it from mains circuit.
Clean the product with a soft dry cloth. If necessary, the cloth may be wetted with water.
7
DISPOSAL INSTRUCTIONS acc. to ElektroG3
1.
waste management of electronic and electrical equipment products
. The symbol „crossed out dustbin“ signifies that you are obliged to recycle these devices separately from unsorted
municipal solid waste. The disposal over domestic waste, e.g. residual waste or yellow recycle bin, is forbidden. Avoid any bad throw by correct disposal at specific collecting points.
2.
extraction of batteries and lamps
. Any batteries, accumulators or lamps which can be removed nondestructively from the legacy device must be cleared from before disposal and must be
disposed separately as batteries or lamps.
3.
return possibilities of legacy devices
. Legacy devices can be submitted free at the public possibilities for return or collection. A proper disposal of the equipment is esured in this way. Under
certain conditions a return to a retailer is also possible.
4.
WEEE registration number
We are registered at the stiftung EAR, Nordostpark 72, 90411 Nürnberg as a distributer of electronic and electrical equipment products by the registration number DE72183678.
WEEE-directive: 2002/96/EG
WEEE-No: DE72183678
8
MISCELLANEOUS
Declaration of Conformity
With the CE sign e+p Elektrik Handels GmbH & Co. KG ensures that this
product corresponds to the standards and directives of the European regulations.
The warranty for this product does only cover the product itself. The manufacturer is not liable for damages to persons or property damage caused by improper installation, operation or maintenance.
If any damage or fault is detected on your product, please contact your local specialist dealer. All rights for misprints, technical changes of product, packaging or documentation reserved.
Elektrik Handels GmbH & Co. KG • Am Ohrt 7 • D-59469 Ense-Höingen
Tel.: 0 29 38 - 98 76 20 • Fax: 0 29 38 - 98 76 22 2 • www.e-und-p.de
Quelle
source
IN
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
