background image

7

E-flite Pitts Model 12 15e ARF Assembly Manual

Non-Warranty Repairs

Should your repair not be covered by warranty the repair 

will be completed and payment will be required without 

notification or estimate of the expense unless the expense 

exceeds 50% of the retail purchase cost.

 By submitting the item 

for repair you are agreeing to payment of the repair without 

notification. Repair estimates are available upon request. You 

must include this request with your repair. Non-warranty repair 

estimates will be billed a minimum of ½ hour of labor. In 

addition you will be billed for return freight. Please advise us 

of your preferred method of payment. Horizon accepts money 

orders and cashiers checks, as well as Visa, MasterCard, 

American Express, and Discover cards. If you choose to pay 

by credit card, please include your credit card number and 

expiration date. Any repair left unpaid or unclaimed after 90 

days will be considered abandoned and will be disposed of 

accordingly. 

Please note: non-warranty repair is only available 

on electronics and model engines.

Electronics and engines requiring inspection or repair should be 

shipped to the following address:

Horizon Service Center 

4105 Fieldstone Road 

Champaign, Illinois 61822

All other Products requiring warranty inspection or repair should 

be shipped to the following address:

Horizon Product Support 

4105 Fieldstone Road 

Champaign, Illinois 61822

Please call 877-504-0233 with any questions or concerns 

regarding this product or warranty.

Safety, Precautions, and Warnings

As the user of this product, you are solely responsible for 

operating it in a manner that does not endanger yourself  

and others or result in damage to the product or the property  

of others.
Carefully follow the directions and warnings for this and any 

optional support equipment (chargers, rechargeable battery 

packs, etc.) that you use.
This model is controlled by a radio signal that is subject to 

interference from many sources outside your control. This 

interference can cause momentary loss of control so it is 

necessary to always keep a safe distance in all directions 

around your model, as this margin will help to avoid collisions 

or injury.

•  Always operate your model in an open area away from cars, 

traffic, or people.

•  Avoid operating your model in the street where injury or 

damage can occur.

•  Never operate the model out into the street or populated 

areas for any reason.

• Never operate your model with low transmitter batteries.
•  Carefully follow the directions and warnings for this and any 

optional support equipment (chargers, rechargeable battery 

packs, etc.) that you use.

•  Keep all chemicals, small parts and anything electrical out of 

the reach of children.

•  Moisture causes damage to electronics. Avoid water exposure 

to all equipment not specifically designed and protected for 

this purpose.

Содержание Pitts Model 12 15e ARF





































Отзывы: