manualshive.com logo in svg

E-FLITE MINI EDGE 540 3D, Инструкция по сборке

Поделиться
Скачать
E-FLITE MINI EDGE 540 3D Скачать руководство пользователя страница 7

7

Warranty Information

Horizon Hobby, Inc. guarantees this kit to be free from 

defects in both material and workmanship at the date of 

purchase. This warranty does not cover any component parts 

damage by use or modification. In no case shall Horizon 

Hobby’s liability exceed the original cost of the purchased 

kit. Further, Horizon Hobby reserves the right to change or 

modify this warranty without notice.

In that Horizon Hobby has no control over the final assembly 

or material used for the final assembly, no liability shall be 

assumed nor accepted for any damage resulting from the 

use of the final assembled product. By the act of using the 

assembled product, the user accepts all resulting liability.

Please note that once assembly of the model has been 

started, you must contact Horizon Hobby, Inc. directly 

regarding any warranty question. Please do not contact 

your local hobby shop regarding warranty issues, even if 

that is where you purchased it. This will enable Horizon to 

better answer your questions and service you in the event 

that you may need any assistance.

If the buyer is not prepared to accept the liability associated 

with the use of this product, the buyer is advised to return this 

kit immediately in new and unused condition to the place of 

purchase.

Horizon Hobby, Inc. 

4105 Fieldstone Road 

Champaign, Illinois 61822 

877-504-0233 

horizonhobby.com

Содержание MINI EDGE 540 3D













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды