E-FLITE MINI EDGE 540 3D Скачать руководство пользователя страница 2

Страница: 2 / 44

Table of Contents

Introduction ................................................................2

Specifications .............................................................2

Contents of Kit/Parts Layout .........................................3

Required Electronics & Accessories ...............................4

Recommended High Performance Motor Setup* .............4

Extreme High Performance Motor Setup* ......................5

Optional Accessories ..................................................5

Additional Tools and Adhesives ....................................5

Important Information About Motor Selection .................6

Using the Manual .......................................................6

Warning ....................................................................6

Before Starting Assembly .............................................6

Warranty Information ..................................................7

Landing Gear Installation .............................................8

Aileron Hinging ........................................................12

Aileron Servos and Linkages ......................................14

Wing Installation ......................................................18

Stabilizer and Elevator ..............................................19

Rudder and Fin ........................................................22

Motor Installation ......................................................25

Rudder and Elevator Servos .......................................28

Receiver, Battery and ESC Install ................................34

Canopy Install ..........................................................36

Cowling Install .........................................................38

Control Throws .........................................................40

Center of Gravity ......................................................41

Range Test Your Radio ...............................................41

2005 Official AMA

National Model Aircraft Safety Code ......42

Introduction

Thank you for purchasing the Mini Edge 540 3D ARF,

which is based on the popular 33% Hangar 9® Edge 540

and is capable of the same extreme 3D performance you

get with larger models. Backed by E-ﬂite’s high quality

reputation, the Mini Edge 540 should provide you with the

superior performance and features you are looking for in an

aerobatic park ﬂyer.

We provide a 6.6:1 gearbox and a 12 x 6 propeller so you

can easily add our E-ﬂite™ Park 400 Brushless motor for

extreme performance. The Mini Edge features lightweight

balsa and light-ply construction, UltraCote® covering,

ﬁberglass cowl and wheel pants, and carbon ﬁber landing

gear. The mid-wing design makes it ideal for aerobatics such

as hovering and other precision 3D maneuvers.

Specifications

Wingspan: 37.25" (945 mm)

Length: 34" (860 mm)

Wing Area: 297 sq in (19 sq dm)

Weight w/o Battery: 20–21 oz (570–595 g)

Weight w/ Battery: 24–26 oz (680–740 g)

Содержание MINI EDGE 540 3D













































Результаты поиска

Содержание MINI EDGE 540 3D

Отзывы:

Похожие инструкции для MINI EDGE 540 3D

Бренды по названию

Популярные бренды

E-FLITE MINI EDGE 540 3D, Инструкция по сборке

Результаты поиска

Содержание MINI EDGE 540 3D

Отзывы:

Похожие инструкции для MINI EDGE 540 3D

Бренды по названию

Популярные бренды