E-FLITE LR-1A Pogo 15e Скачать руководство пользователя страница 7

Страница: 7 / 40

E-flite LR-1A Pogo 15e ARF Assembly Manual

Joining the Wing Panels

Required Parts

Left wing panel

Right wing panel

Aluminum wing tube

Required Tools and Adhesives (optional)

30-minute epoxy

Mixing cups

Mixing sticks

Paper towels

Rubbing alcohol

Epoxy brush

Using epoxy to glue the wing is optional. Make sure

your vehicle is large enough to fit the assembled

wing before gluing the two panels together. Read

through the following steps before mixing any epoxy.



1. Slide the aluminum wing tube into one of the

wing panels. The tube will only slide in half-way.

Do not force the tube to slide further than it will

easily slide.



2. Mix 1/2-ounce (15ml) of 30-minute epoxy. Use

an epoxy brush to apply a thin layer of epoxy on

the root of both the left and right wing panels as

shown.



3. Slide the remaining wing panel onto the

aluminum wing tube.



4. The tab from the right wing panel will key into

the left wing panel. Rotate the panels as shown

to insert the tab from the right panel into the left

panel.



5. Rotate the panels so they are in alignment.

If you have used epoxy to join the panels,

use a paper towel and rubbing alcohol to

remove any excess epoxy from the wing. Set

the wing aside until the epoxy fully cures.

Содержание LR-1A Pogo 15e









































Результаты поиска

Содержание LR-1A Pogo 15e

Отзывы:

Похожие инструкции для LR-1A Pogo 15e

Бренды по названию

Популярные бренды

E-FLITE LR-1A Pogo 15e, Инструкция по сборке

Результаты поиска

Содержание LR-1A Pogo 15e

Отзывы:

Похожие инструкции для LR-1A Pogo 15e

Бренды по названию

Популярные бренды