background image

6

E-flite Hawker Sea Fury 400 ARF Assembly Manual

Damage Limits

HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT OR 

CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION 

OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE 

PRODUCT, WHETHER SUCH CLAIM IS BASED IN CONTRACT, 

WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. Further, in no 

event shall the liability of Horizon exceed the individual price of the 

Product on which liability is asserted. As Horizon has no control over 

use, setup, final assembly, modification or misuse, no liability shall be 

assumed nor accepted for any resulting damage or injury. By the act 

of use, setup or assembly, the user accepts all resulting liability.
If you as the Purchaser or user are not prepared to accept the liability 

associated with the use of this Product, you are advised to return this 

Product immediately in new and unused condition to the place of 

purchase.
Law: These Terms are governed by Illinois law (without regard to 

conflict of law principals).

Safety Precautions

This is a sophisticated hobby Product and not a toy. It must be 

operated with caution and common sense and requires some basic 

mechanical ability. Failure to operate this Product in a safe and 

responsible manner could result in injury or damage to the Product or 

other property. This Product is not intended for use by children without 

direct adult supervision. The Product manual contains instructions for 

safety, operation and maintenance. It is essential to read and follow 

all the instructions and warnings in the manual, prior to assembly, 

setup or use, in order to operate correctly and avoid damage or 

injury.

Questions, Assistance, and Repairs

Your local hobby store and/or place of purchase cannot provide 

warranty support or repair. Once assembly, setup or use of the 

Product has been started, you must contact Horizon directly. This will 

enable Horizon to better answer your questions and service you in the 

event that you may need any assistance. For questions or assistance, 

please direct your email to [email protected], or call 

877.504.0233 toll free to speak to a service technician.

Inspection or Repairs

If this Product needs to be inspected or repaired, please call for a 

Return Merchandise Authorization (RMA). Pack the Product securely 

using a shipping carton. Please note that original boxes may be 

included, but are not designed to withstand the rigors of shipping 

without additional protection. Ship via a carrier that provides tracking 

and insurance for lost or damaged parcels, as 

Horizon is not 

responsible for merchandise until it arrives and is accepted 

at our facility

. A Service Repair Request is available at www.

horizonhobby.com on the “Support” tab. If you do not have internet 

access, please include a letter with your complete name, street 

address, email address and phone number where you can be reached 

during business days, your RMA number, a list of the included items, 

method of payment for any non-warranty expenses and a brief 

summary of the problem. Your original sales receipt must also be 

included for warranty consideration. Be sure your name, address, and 

RMA number are clearly written on the outside of the shipping carton.

Warranty Inspection and Repairs

To receive warranty service, you must include your original 

sales receipt

 verifying the proof-of-purchase date. Provided warranty 

conditions have been met, your Product will be repaired or replaced 

free of charge. Repair or replacement decisions are at the sole 

discretion of Horizon Hobby.

Содержание hawker sea fury 400 arf









































Отзывы: