background image

4

E-flite F-15 Eagle ARF Assembly Manual

Required Tools and Adhesives

Tools & Equipment

EFLA250 

Park Flyer Tool Assortment, 5-piece

Or Purchase Separately

EFLA257 

 Screwdriver, #1 and #2 Phillips  

(or included with EFLA250)

Hex wrench: 1.5mm 

6-minute epoxy

Hobby knife 

Clear tape

Phillips screwdriver: #1 

Hobby knife

Side cutters 

String

Painter's tape 

Canopy glue

Ruler 

Threadlock

Rotary tool with sanding drum and high speed grinding bit

Optional Accessories

EFLA110 

Power Meter

EFLC3005 

Celectra

 1- to 3-Cell Li-Po Charger

EFLC505 

Intelligent 1- to 5-Cell Balancing Charger

THP21003SPL 

2100mAh 3S 11.1V Li-Po Battery

Using the Manual

This manual is divided into sections to help make assembly 

easier to understand, and to provide breaks between each major 

section. In addition, check boxes have been placed next to each 

step to keep track of each step completed. Steps with a single 

circle (

) are performed once, while steps with two circles (

 

indicate that the step will require repeating, such as for a right or 

left wing panel, two servos, etc.

Remember to take your time and follow the directions.

Warranty Information

Warranty Period

Horizon Hobby, Inc., (Horizon) warranties that the Products purchased 

(the “Product”) will be free from defects in materials and workmanship 

at the date of purchase by the Purchaser.

Limited Warranty

(a) This warranty is limited to the original Purchaser ("Purchaser") and 

is not transferable. REPAIR OR REPLACEMENT AS PROVIDED UNDER 

THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE PURCHASER. 

This warranty covers only those Products purchased from an 

authorized Horizon dealer. Third party transactions are not covered 

by this warranty. Proof of purchase is required for warranty claims. 

Further, Horizon reserves the right to change or modify this warranty 

without notice and disclaims all other warranties, express or implied.
(b) Limitations- HORIZON MAKES NO WARRANTY OR 

REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-

INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A 

PARTICULAR PURPOSE OF THE PRODUCT. THE PURCHASER 

ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT 

THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE 

PURCHASER’S INTENDED USE.
(c) Purchaser Remedy- Horizon's sole obligation hereunder  

shall be that Horizon will, at its option, (i) repair or (ii) replace, any 

Product determined by Horizon to be defective. In the event of a 

defect, these are the Purchaser's exclusive remedies. Horizon reserves 

the right to inspect any and all equipment involved in a warranty 

claim. Repair or replacement decisions are at the sole discretion of 

Horizon. This warranty does not cover cosmetic damage or damage 

due to acts of God, accident, misuse, abuse, negligence, commercial 

use, or modification of or to any part of the Product. This warranty 

does not cover damage due to improper installation, operation, 

maintenance, or attempted repair by anyone other than Horizon. 

Return of any goods by Purchaser must be approved in writing by 

Horizon before shipment.

Содержание F-15 Eagle





































Отзывы: