E-FLITE AT-6 25e Texan ARF Скачать руководство пользователя страница 49

Страница: 49 / 52

E-flite AT-6 Texan ARF Assembly Manual

Center of Gravity

An important part of preparing the aircraft for flight is properly

balancing the model.

Caution: Do not inadvertently skip this step!

The recommended Center of Gravity (CG) location for the AT-6
Texan ARF is 4

– 4

-inch (105–108mm) back from the

leading edge of the wing wheel fairing. Please balance your

model upside down with the battery installed. Gear placement

of up or down does not matter.

After the first flights, the CG position can be adjusted for your

personal preference.
You may need to add some weight to the nose of your model to

achieve the desired CG. We had to add 2 ounces to the inside

of the cowling on our prototypes. Use commercially available

stick-on weights for this.

Preflight

Check Your Radio

Before going to the field, be sure that your batteries are fully

charged per the instructions included with your radio. Charge

both the transmitter and receiver pack for your airplane. Use

the recommended charger supplied with your particular radio

system, following the instructions provided with the radio. In

most cases, the radio should be charged the night before going

out flying.
Before each flying session, be sure to range check your radio.

See your radio manual for the recommended range and

instructions for your radio system. Each radio manufacturer

specifies different procedures for their radio systems. Next, start

the motor. With the model securely anchored, check the range

again. The range test should not be significantly affected. If it is,

don’t attempt to fly! Have your radio equipment checked out by

the manufacturer.

Note

: Keep loose items that can get entangled in

the propeller away from the prop. These include

loose clothing, or other objects such as pencils and

screwdrivers. Especially keep your hands away from the

propeller.

Double-check that all controls (aileron, elevator, rudder and

throttle) move in the correct direction.
Check the radio installation and make sure all the control

surfaces are moving correctly (i.e. the correct direction and with

the recommended throws). Test run the motor and make sure

it transitions smoothly from off to full throttle and back. Also

ensure the engine is installed according to the manufacturer’s

instructions, and it will operate consistently.
Check all the control horns, servo horns, and clevises to make

sure they are secure and in good condition. Replace any items

that would be considered questionable. Failure of any of these

components in flight would mean the loss of your aircraft.

Содержание AT-6 25e Texan ARF





















































Результаты поиска

Содержание AT-6 25e Texan ARF

Отзывы:

E-FLITE AT-6 25e Texan ARF, Инструкция по сборке, Страница: 49 / 52

Результаты поиска

Содержание AT-6 25e Texan ARF

Отзывы: