manualshive.com logo in svg

Dynorbital-Spirit 59000, Безопасность, эксплуатация и обслуживание, Страница: 5 / 12

Поделиться
Скачать
Dynorbital-Spirit 59000 Скачать руководство пользователя страница 5

Machine Exhaust Assemblies

Self Generated Vacuum (Vac-Ready)/Machine Exhaust

Central Vacuum/Machine Exhaust

Non-Vacuum/Machine Exhaust

Vacuum Conversion Instructions

..

To Disassemble:

1. Disconnect tool from power source.  Invert machine and secure in vise, using 57092 Collar (supplied in 57098 Repair Kit) or padded jaws.
2. Remove sanding pad with 50679 (26 mm) Open-End Wrench (supplied with sander) and lip-seal shroud from housing.
3. Remove 56028 Muffler Cap and 56027 Muffler Insert (2) from 57066 Muffler Body.  Using a 12 mm hex wrench (supplied in 57098 Repair Kit), remove 

muffler body from housing (not applicable for Self-Generated Vac to Central Vac).

Non-Vac to Self-Generated Vac for Hook-Up to Self-Contained Dust Collection System

1. Attach 57083 Vacuum Adapter to either 57084, 57086, 57087 Vacuum Overskirts or 57089 Vacuum Lip-Seal Shroud.  Then attach to the housing making

sure the protrusions on the overskirt or shroud are aligned with the notches on the housing.

2. Place 95526 O-Ring on the muffler body between the shoulder and the four (4) protrusions.  Using a 12 mm hex wrench, attach the muffler body and

o-ring to the housing through the vacuum adapter.

3. Place vacuum nozzle into the vacuum adapter with the slots facing outward making sure that the knob on the nozzle is aligned with the slot in the adapter.
4. Place 57067 Vacuum Tube into the vacuum adapter with the grooves facing inward until the adapter “snaps” onto the tube and the tube cannot be pulled 

out.  If the tube can be pulled out, rotate it 1/4 turn and place it back into the adapter until it “snaps”.

5. Rotate tube until holes line up.  Insert dowel pin in holes until it is centered.  Attach sanding pad, attach machine to portable dust collection system.

Non-Vac to Central Vac

1. Attach 57093 Vacuum Adapter to either 57084, 57086, 57087 Vacuum Overskirts or 57089 Vacuum Lip-Seal Shroud.  Then attach to the housing making

sure the protrusions on the overskirt or shroud are aligned with the notches on the housing.

2. Using a 12 mm hex wrench, attach the muffler body to the housing through the central vacuum adapter.
3. Place muffler cap with inserts on muffler body making sure that the protrusions on the body fit in the pockets on the cap.
4. Attach weight-mated vacuum sanding pad with 50679 (26 mm) Open-End Wrench.  Attach machine to central vacuum system.

Self-Generated Vac to Central Vac

1. Remove 96197 Dowel Pin with an 1/8" drive pin.  Remove 57067 Vacuum Tube from 57083 Vacuum Adapter by turning it clockwise while pulling backward.
2. Using a small flat screwdriver, pry vacuum nozzle until it is loose and then remove it by using two fingers to push and pull it until it hits the “legs” on 

vacuum adapter.  Place vacuum tube back into vacuum adapter far enough to push the “legs” back then push vacuum nozzle and vacuum tube
out the rest of way. 

3. Using a 12 mm hex wrench (supplied in 57098 Repair Kit), remove the 57066 Muffler Body and 95526 O-Ring from the housing through the adapter.  

Remove the o-ring from the muffler body.

4. Remove 57083 Vacuum Adapter and attach 57093 Vacuum Adapter to either 57084, 57086, 57087 Vacuum Overskirts or 57089 Vacuum Lip-Seal Shroud.

Then attach to the housing making sure that the protrusions on the overskirt or shroud are aligned with the notches on the housing.

5. Using a 12 mm hex wrench, attach the muffler body and o-ring to the housing through the central vacuum adapter.
6. Place muffler cap with inserts on muffler body making sure that the protrusions on the body fit in the pockets on the cap.  Attach sanding pad.

Central Vac to Self Generated Vac

1. Remove 57093 Central Vacuum Adapter and put the 57083 Vacuum Adapter in its place.

(continued on next page)

Index Key

No.

Part #

Description

1

57083 Vacuum Adapter

2

96197 Dowel Pin

3

57066 Muffler Body

4

95526 O-Ring 

5

59088 Vac Nozzle

6

57067 Vac Tube

7

57093 Vacuum Adapter

8

56027 Muffler Insert (2)

9

56028 Muffler Cap

10

59273 Muffler Assembly

1

2

3

7

3

8

9

3

8

9

10

4

5

6

Non-Vacuum to Vacuum Conversion Kits

Original

Converts

Kit

Non-Vac Tool

to

Part Number

3-1/2" (89 mm)

Self-Generated Vac-Ready

57118

3-1/2" (89 mm)

Central Vac-Ready

57119

5" (127 mm)

Self-Generated Vac-Ready

57120

5" (127 mm)

Central Vac-Ready

57121

6" (152 mm)

Self-Generated Vac-Ready

57122

6" (152 mm)

Central Vac-Ready

57123

Optional:  30 quantity Muffler Insert available, P/N 56054.

Содержание 59000













Отзывы:

Нет отзывов