Dynorbital-Spirit 59000 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 12

Dynorbital-Spirit 59000 Скачать руководство пользователя страница 2

To Tool Station

Closed Loop Pipe System

(Sloped in the direction of air flow)

Ball

Valve

Ball

Valve

Filter

Coupler

Regulator

Lubricator

Air Flow

Drain
Valve

Drain
Valve

Air Tool

Air Compressor

and Receiver

Drain Valve

Air Hose

90 PSIG MAX

(6.2 Bar)

Air Flow

Refrigerated

Air Dryer

2

Filter

Regulator

Lubricator

90 PSIG

(6.2 Bar)

OPERATING INSTRUCTIONS (continued)

• Keep hand and clothing away from working end of the air tool.

Operation: Be sure that any loose clothing, hair and all jewelry is properly restrained.

• Secure inlet bushing on air tool with a wrench before attempting to install the air fitting to avoid damaging housing assembly.
• Check tool RPM (speed) with tachometer with air pressure set at 90 PSIG while the tool is running. If tool is operating at a higher speed than the RPM marked on the tool

housing, or operating improperly, the tool must be serviced and corrected before use.

Caution: Tool RPM must never exceed abrasive/accessory RPM rating. Check accessory manufacturer for details on maximum operating speed or special

mounting instructions.

• With power source disconnected from air tool, mount recommended accessory into collet assembly.
• Connect air tool to power source. Be careful NOT to depress throttle lever in the process. Do not expose air tool to inlet pressure above 90 PSIG or (6.2 Bars).

Caution: After installing the accessory, before testing or use and/or after assembling tool, the Dynorbital-Spirit™ must be started at a reduced speed to check for good

balance. Gradually increase tool speed. DO NOT USE if tool vibration is excessive. Correct cause, and retest to insure safe operation.

• Make sure that work area is uncluttered, and visitors are at a safe range from the tools and debris.
• Use a vise or clamping device to hold work piece firmly in place.
• Do not apply excessive force on tool or apply “rough” treatment to it.
• Always work with a firm footing, posture and proper lighting.

Report to your supervisor any condition of the tool, accessories, or operation you consider unsafe.

Air System

1

DROP/MIN.

20

SCFM

LUBRICATOR SETTING

•

Ideally the air supply should be free from moisture.
Incorporating a refrigerated air dryer after the
compressor and drain valves at each tool station
(as shown) further reduces moisture from
condensation in the air supply.

•

Dynabrade Air Power Tools are designed to
operate at 90 PSIG (6.2 Bar/620 kPa) maximum
air pressure at the tool inlet, when the tool is
running. Use recommended regulator to control
air pressure.

➤

➤

➤

➤

➤

➤

«
1
2
3
4
...
»

Содержание 59000













Отзывы:

Нет отзывов