background image

DYNISCO PG500 Series

8

88

8

8

8

88

8

8

5.

REMOVAL

Because the gauge incorporates a sensitive lower sensing diaphragm,
removal of the instrument from the mounting hole should be
attempted only with the extruder barrel hot. Failure to do could
cause damage due to frozen polymer in the mounting hole adhering
to the diaphragm.

6.

CLEANING

Once the unit is removed from the mounting hole, the stem can be
wiped clean with a dry cloth. *Do not attempt to clean the sensing
diaphragm with a wire brush, screwdriver, etc.

7.

WARRANTY AND SERVICE

This equipment is sold subject to the mutual agreement that it is free
from defects of material and construction. Our liability in connection
with it shall be limited to the replacement or repair, without charge at
our factory, of any material or construction defect that becomes
apparent within two years from the date that the products are
shipped. We are not liable for damages of any kind arising from the
installation or use of our products or both.

Damaged transducers should be returned to:

DYNISCO INSTRUMENTS

38 Forge Parkway

Franklin, MA 02038

Attn:  Repair Dept.  RA #__________________

Please call for a Return Authorization Number
 before returning product to Dynisco.

Questions concerning warranty, repair cost, and delivery should be
directed to the Dynisco Repair Department, telephone number 508-
541-9400 or E-mail: [email protected]

For

For

For

For

For

technical

technical

technical

technical

technical

assistance,

assistance,

assistance,

assistance,

assistance,

call:

call:

call:

call:

call:

800-221-2201

800-221-2201

800-221-2201

800-221-2201

800-221-2201

Содержание PG 552












Отзывы: