background image

 

 

Introduction

Please read the Important Safety Instructions supplied with these speakers before 
beginning their installation.

The OW-6 and OW-8 are custom installation, wall-mount, passive high-performance 

speakers suitable for installation both inside and outdoors. They are supplied with 
adjustable wall-mount brackets and can be powered by both conventional “low-z” 
amplification or 100V/70V line amplification.

OW Series speakers are intended to be mounted either vertically or horizontally using the 
supplied wall-mount brackets. The brackets can be attached to any suitably sound 
structure. Wall-mount fittings such as screws and wall plugs are not supplied but should be 

chosen appropriately for the type and condition of the structure the wall-mount brackets 
are to be attached to. OW Series speakers are heavy and you must be sure that the 
structure and fittings chosen are able to support a minimum of 20 kg. If you have any 

concerns over the suitability of the structure, or doubt in your ability to fix the wall-mount 
brackets securely, you should seek professional advice and help.

A tapped hole is provided on the rear panel of OW Series speakers to enable the supplied 
secondary restraint eyelet and a chain to be fitted. Secondary restraint is compulsory in 

some territories.

OW Series speakers are rated water and dust resistant to IP65. They can be installed in 
the open air but should be sheltered from rain and direct sunlight. They can also be 

installed and used in environments that are subject to long-term ambient temperatures 
between -33 °C and +40 °C. They are not suitable for installation where they will be 
continually in contact with water.

Note

Water and dust resistance to IP65 is only achieved with a single cable connection to OW 
Series speakers. With multiple cable connections, OW Series speakers are rated to IP44.

This manual is divided into sections covering carton contents, positioning, connecting, 
configuration and mounting. Please read all the sections before beginning speaker 
installation.

Note

Visit 

dynaudio.com

 for the latest Outdoor series news and information.

Содержание OW Series















Отзывы: