Operation
Owner’s manual
9
Operation
Switching the subwoofer on
5. Operation
8
Dynaudio Acoustics BM14S
Connecting loudspeakers
If your source provides bass management, you can use the BM14S LFE input alone
in LFE or SLAVE mode, depending on the management system capabilities. Avoid
double processing if possible.
To connect loudspeakers
1.
Connect the subwoofer (see “Connecting a single subwoofer” on page 8).
2.
From the subwoofer
SAT/SUB
output connect a XLR cable to the inputs
of the
power amplifier you use for your speakers.
Operation
Switching the subwoofer on
Once you have ensured yourself that all necessary connections have been made, the
subwoofer and the connected components can be switched on.
1.
Connect the subwoofer to the mains power.
2.
Switch the subwoofer on with the main
POWER
switch on the rear panel.
The status LED on the rear of the subwoofer will light up red.
3.
Select a power mode with the
Power
switch on the rear panel.
Power modes
•
On
: the subwoofer is switched on permanently
•
Auto
– When a music signal is detected, the internal amplifier is activated
automatically. The status LED on the back of the subwoofer will light up green.
As long as a music signal is available on the subwoofer’s input, it will remain
switched on.
– After 15 to 20 minutes of not sensing any input music signal, the subwoofer will
switch itself to Standby mode automatically. The status LED on the back of the
subwoofer will light up red.
Note:
The signals connected to the inputs are provided at the
Slave
output for
connecting another subwoofer. See page 8 to learn more about connecting
multiple subwoofers.
Note:
To switch the subwoofer completely off, set the main
POWER
switch to the
OFF
position.
LFE
Stereo
To power amplifier
or active speakers
2.
3.
1.
Once you have ensured yourself that all necessary connec-
tions have been made, the subwoofer and the connected
components can be switched on.
1. Connect the subwoofer to the mains power.
2. Switch the subwoofer on with the main POWER switch on
the rear panel. The status LED on the rear of the subwoof-
er will light up red.
3. Select a power mode with the Power switch on the rear
panel.
Power modes
–
On:
the subwoofer is switched on permanently
–
Auto
– When a music signal is detected, the internal ampli-
fier is activated automatically. The status LED on the
back of the subwoofer will light up green. As long as
a music signal is available on the subwoofer’s input, it
will remain switched on.
– After 15 to 20 minutes of not sensing any input music
signal, the subwoofer will switch itself to Standby
mode automatically. The status LED on the back of
the subwoofer will light up red.
Note:
To switch the subwoofer completely off, set the main POWER
switch to the OFF position.
Adjusting the volume (Gain)
CAUTION
High Sound Levels!
High sound levels can cause auditory defects.
– To avoid auditory defects, do not listen to high sound lev-
els over a longer period of time.
5. Operation
Dynaudio Acoustics BM14S
9
Adjusting the volume (Gain)
The correct volume setting is an important aspect in achieving a well balanced
speaker combination.
To adjust the gain:
Adjust the
Gain
control, until correct setting is reached.
Selecting the subwoofer cut-off frequency
(Lowpass)
The
Lowpass
control allows the frequency range of the subwoofer to be defined.
Above the selected frequency the sound level decreases rapidly. The correct setting
of this cut-off frequency is important for a well balanced combination of subwoofer and
speakers.
To selec the cut-off frequency
Set the
Lowpass
control to the desired frequency between 50 and 150 Hz.
Please also heed the instructions given in the operating manual of your
loudspeakers.
CAUTION
High Sound Levels!
High sound levels can cause auditory defects.
To avoid auditory defects do not listen to high sound levels over a longer period
of time.
Note:
You cannot adjust the volume, when subwoofer is in slave mode. In this case
the volume is controlled by the setting of the master subwoofer.
Note:
• The
Lowpass
only works on
SAT/SUB
input.
• Perhaps subwoofer cut-off frequency is already set in the bass
management of your source. Please refer to the operating manual of
your source. In general use only one bass management system.
The correct volume setting is an important aspect in achieving
a well balanced speaker combination.
To adjust the gain:
– Adjust the Gain control, until correct setting is reached.
Note:
You cannot adjust the volume when the subwoofer is in slave
mode. In this case the volume is controlled by the setting of
the master subwoofer.
Dynaudio Professional BM14S II manual.indd 9
2014-02-24 14:45
Содержание BM14S II
