Dynatronix Diamond 10kW Series Скачать руководство пользователя | Manualshive

Страница: 80 / 150

background image

Page 80 of 150

198-1603-03 Rev 01

A.1 Menu Tree Format

    



    

Indicates rotating the associated encoder. The location of this symbol indicates which
encoder switch is being referenced.

Indicates pushing the associated encoder switch. The location of this symbol indicates
which encoder switch is being referenced.

Indicates the grayed text in the associated display is blinking on and off. A display that
blinks on and off indicates a parameter that can be changed.

Used to indicate the next screen in a multi-screen message. In a multi-screen message
the display will show a short phrase by alternating text one word at a time. This symbol
is used to show the order of the screens displayed.

Indicates no action is taken to the associated encoder switch. The location of this
symbol indicates which encoder switch is being referenced.

Symbol Definitions

Example

Totalizer
Configuration
Menu

Pushing the voltage encoder from the shown
screen will enter the totalizer configuration
menu.



Rotating the current
encoder changes
between the “tot” and
the “HOSt” selection.

The grayed text (“HOSt”) is
blinking on and off.

«
...
78
79
80
81
82
...
»

Содержание Diamond 10kW Series























































































































































Отзывы:

Нет отзывов

Похожие инструкции для Diamond 10kW Series

Бренд: MACROZA Страницы: 13

Бренд: Gechter Страницы: 60

Бренд: SOMMER Страницы: 20

Бренд: Sanela Страницы: 2

Бренд: Far Tools Страницы: 30

Бренд: Ford Страницы: 11

Бренд: Wacker Neuson Страницы: 144

Бренд: Clearaudio Страницы: 12

Бренд: Parkside Страницы: 51

Бренд: Rikon Power Tools Страницы: 16

Бренд: Black Ridge Страницы: 16

Бренд: deltalight Страницы: 2

Бренд: Kolver Страницы: 3

Бренд: Unimac Страницы: 7

Бренд: ENKHO Страницы: 50

Бренд: RED ROOSTER Страницы: 11

Бренд: Panasonic Страницы: 44

Бренд: Parkside Страницы: 163

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды