(FIGURE 1)
Next, slide the Head Support’s vertical post through the
mounting bracket and secure in place using the latch clamp
(see Figure 3). The channel in the vertical post should slide
over the Channel Screw (illustrated in Figure 2), ensuring
the post cannot rotate after installation.
Set the post to the desired height, and slide the locking
collar down to the top of the mounting kit. Secure in place
by tightening its screw against the head support vertical
post. This will ensure that the height of the head support
will always return to same height that it is set to.
Step 3 – Head Pad
Unzip the back of the pad cover exposing the inside of the
pad. Set the ball on the head support into the received
inside the back of the pad. Secure using the 3 screws
provided (see Figure 4). The head pad can then be bent in
or out to customize the fit to the user’s head.
OPTIONAL STEP – Install Flip Back Hardware (if ordered)
To install the optional flip back hardware, first remove the
head support arm by unfastening the hardware (3 pieces)
that secures it (see Figure 5). Set the hardware and head
support arm aside to reattach after the flip back has been
installed.
Next, install the flip back post extension over
the existing post. With the hardware
provided with, secure the flip back extension
by inserting the latch clamp through the
channel (with thin washer and heavy duty
washer) and tightening the special nut on the
other side.
Note: both the heavy duty washer and the special
nut must be installed with the small two sided
protrusion going into the elongated holes on each
side of the flip back post extension
(Figure 4)
Screws used to secure
Pad to Head Support
(Figure 5)
Support Arm
Hardware
Latch Clamp
(Figure 3)
Flip Back
Post Extension
Special Nut
Latch Clamp
Thin Washer
Heavy Duty Washer
(Figure 6)
Locking
Collar
(Figure 4)
Locking Collar
Collier de
verrouillage
Locking Handle
Poignée de ver-
rouillage
(FIGURE 3)
HEAD SUPPORT INSTALLATION
INSTALLATION DESUPPORT DE TÊTE
Tool Required:
4mm Allen Key /
Outil requis:
Clé Allen 4mm
(FIGURE 2)
Channel screw used to
adjust Head Support orien-
tation
Vis de canal utilisée pour
ajuster l’orientation du
support de tête
Step /
Étape
#
1
Mounting Kit /
Kit de montage
(Figure 1)
Attach the mounting kit hardware to the back
shell using the 2 screws and washes provided
(also applies to Universal Mount)
Fixez le matérial du kit de montage à la coque
arrière en utilisant les vis et les rondelles fournies
(s’applique également à un support universel)
Step /
Étape
#
2
Head Support /
Support de tête
The Head Support’s post can be installed in one of three
orientations - center, left, or right. To change the orientation, move
the channel screw, located on the inside of the Mounting Bracket,
to the appropriate location.
Next, slide the Head Support’s vertical post through the
mounting bracket and secure in place using the locking handle
(Figure 3). The channel in the vertical post should slide over the
Channel Screw (Figure 2), ensuring the post cannot rotate after
installation.
Set the post to the desired height, and slide the locking collar
down to the top of the mounting kit. Secure in place by tightening
its screw against the head support vertical post. This will ensure
that if the head support is removed, the height of the head
support will always return to same height that it is set to when
re-installed .
Le poste de Support de tête peut être installé dans l’une des trois
orientations - centre, gauche ou droite. Pour changer l’orientation,
déplacez la vis du canal, située à l’intérieur du support de
montage, à l’emplacement approprié.
Ensuite, faites glisser le montant vertical du support de tête à
travers le support de montage et fixez-le à l’aide de la poignée
de verrouillage (Figure 3). Le canal dans le montant vertical doit
glisser sur la vis du canal (Figure 2), en s’assurant que le montant
ne puisse pas tourner après l’installation.
Réglez le montant à la hauteur désirée, et faites glisser le collier
de verrouillage vers le haut du kit de montage. Fixez en place
en serrant sa vis contre le montant vertical du support de tête.
Cela garantira que si le support de tête est retiré, la hauteur du
support de tête reviendra toujours à la même hauteur que celle
qui est définie lors de la réinstallation.
3
3
