Dynamic DX-SLM Скачать руководство пользователя

Страница: 49 / 52

GBK60027 DX-SLM Installation Manual Issue 5

Maintenance

All Dynamic electronic components should be kept free of dust, dirt and liquids.

For cleaning the product, use a cloth dampened with warm soapy water. Do not

use chemicals, solvents or abrasive cleaners, as this may cause damage to the

product.

All vehicle components should be regularly checked for loose, damaged or

corroded components such as connectors, terminals, or cabling. All cables should

be restrained to protect them from damage. Damaged components should be

replaced.

All switchable functions on the Dynamic electronics system should be regularly

tested to ensure they function correctly.

There are no user-serviceable parts in any Dynamic electronic component. Do

not attempt to open any case or undertake any repairs, else warranty will be

voided.

Where any doubt exists, consult your nearest service centre or agent.

Warning:
If any component is damaged in any way, or if internal damage may have
occurred (for example by being dropped), have it checked by qualified
personnel before operating.

Page 47

Содержание DX-SLM





















































Результаты поиска

Содержание DX-SLM

Отзывы:

Похожие инструкции для DX-SLM

Бренды по названию

Популярные бренды

Dynamic DX-SLM, Руководство по установке

Результаты поиска

Содержание DX-SLM

Отзывы:

Похожие инструкции для DX-SLM

Бренды по названию

Популярные бренды