Dynamatic EC 2000 Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 46

background image

41

8.6

FOLLOWER OR POTENTIOMETER SIGNAL NOT CHANGING SETPOINT

•

Verify the control is in the right mode. “AUTO” mode corresponds to an automatic follower
signal. “REMOTE” mode corresponds to a signal that is external to the keypad.

•

Check to see if any external connections into TB2 are improperly grounded. Recheck the
wiring diagrams seen in Figures 8 through 13. If multiple signals are wired into TB2, try
disconnecting signals one by one to eliminate possible issues.

•

Verify the signals are present at TB2.

8.7

UNSTABLE SPEED

•

Adjust the PID loop parameters in Menu B.

8.8

SPEED ON DISPLAY IS DIFFERENT THAN ACTUAL SPEED

•

Verify that the Tach Pulses/REV setting in Menu A, Parameter 5 matches your mechanical
unit. If unknown, try another setting and see if the displayed speed is closer to the actual
speed.

8.9

SCREEN IS FROZEN AND/OR HAS UNFAMILIAR CONTENT

•

Try resetting the EC 2000 either by pushing “SW1” on the 15

-1200-1 board or by removing

all TB2 connections and placing a jumper between TB2-32 and TB2-29.

8.10

SCREEN IS LIT, BUT NOTHING IS DISPLAYED

•

Try resetting the EC 2000. If the issues persists, check to see if the keypad cable is inserted
correctly or not damaged.

8.11

LOCAL/REMOTE KEY DOES NOT WORK

•

Check to see if “LOCAL/REM ENABLE” is enabled in Menu A, Parameter 12.

8.12

DRIVE SLOWER THAN DESIRED

•

Check to see if the clutch current limits are properly set in Menu A, Parameter 4.

«
...
39
40
41
42
43
...
»

Содержание EC 2000















































Отзывы:

Нет отзывов

Похожие инструкции для EC 2000

Бренд: GBD Страницы: 12

Evolution Series E9000

Бренд: GE Страницы: 44

PACSystems RX7i

Бренд: GE Страницы: 469

GuardSwitch 300 Series

Бренд: GE Страницы: 2

GuardSwitch 300 Series

Бренд: GE Страницы: 2

Masoneilan VariPak 28001

Бренд: GE Страницы: 24

Бренд: Jafar Страницы: 10

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 2

Бренд: Danfoss Страницы: 12

Бренд: Danfoss Страницы: 24

Бренд: Danfoss Страницы: 60

Бренд: Danfoss Страницы: 10

Бренд: Danfoss Страницы: 20

Бренд: Gascat Страницы: 32

VARIVENT D Series

Бренд: GEA Страницы: 78

Бренд: GEA Страницы: 96

Бренд: GEA Страницы: 66

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды