background image

 Easy-to-Build • All Wood Hand-Launched Glider

• 2-Channel Radio Required

(mini servos recommended)

BEFORE STARTING CONSTRUCTION, READ THROUGH THIS INSTRUCTION

MANUAL. IT CONTAINS IMPORTANT INSTRUCTIONS AND WARNINGS
CONCERNING THE ASSEMBLY AND USE OF THIS MODEL.

WARRANTY

Dynaflite guarantees this kit to be free from defects in both material and workmanship at the date of
purchase. This warranty does not cover any component parts damaged by use or modification. In no
case shall Dynaflite's liability exceed the original cost of the purchased kit. Further, Dynaflite reserves
the right to change or modify this warranty without notice. In that Dynaflite has no control over the
final assembly or material used for final assembly, no liability shall be assumed nor accepted for any
damage resulting from the use by the user of the final user-assembled product. By the act of using
the user-assembled product, the user accepts all resulting liability. If the buyer is not prepared to

accept the liability associated with the use of this product, return this kit immediately in new and
unused condition to the place of purchase.

SKTRP03 Printed in USA Entire Contents © Copyright 1996

Содержание Skeeter













Отзывы: