Dynabrade Mini-Raptor Vac 61100, Руководство пользователя

Страница: 10 / 14

PROUDLY DESIGNED, ENGINEERED, AND BUILT IN AMERICA SINCE 1969
Dynabrade, Inc. 8989 Sheridan Drive | Clarence, New York 14031 | dynabrade.com
PROUDLY DESIGNED, ENGINEERED, AND BUILT IN AMERICA SINCE 1969
Dynabrade, Inc. 8989 Sheridan Drive | Clarence, New York 14031 | dynabrade.com
53. Your vacuum can be used as a
powerful blower. To use your unit as
a blower, unscrew blower port cover
located on the backside of the tank
cover. Clear hose of any
obstructions. Insert machine hose
end with locking nut into blower port
and tighten locking-nut. FIGURE 36 . Do not over-
tighten. Caution should be used when using as a blower
due to the powerful force of air when using certain
attachments.
NOTE: For maximum performance, when vacuuming,
remove blower port cover.
BLOWER
FEATURE
EMPTYING
LIQUID
WASTE FROM
THE TANK
FIGURE 36
WARNING!
FIGURE 35
FOAM SLEEVE INSTALLATION AND CLEANING:
(Not standard)
48. With tank cover in an upside
down position, slide foam sleeve
down over lid cage pulling until foam
sleeve completely covers lid cage.
FIGURE 35.
49. To clean the foam sleeve, disconnect the plug from
the wall outlet. Remove the tank cover and place the
cover in an upside-down position. Remove foam sleeve
by sliding it up and off the lid cage.
50. Shake excess debris off of the foam sleeve with a
rapid up and down movement.
51. Hold foam sleeve under running water for a minute
or two, rinsing from the inside of the filter. A water wash
is not always required, depending on the condition of
the foam sleeve.
52. Check the filter for tears. If any are found, replace
with a new filter.
ALWAYS WEAR EYE PROTECTION TO PREVENT
ROCKS OR DEBRIS FROM BEING BLOWN OR
RICOCHETING INTO THE EYES OR FACE WHICH
CAN RESULT IN SERIOUS INJURY.
47. Before storing the vacuum cleaner or using for dry
pick up, clean and dry the interior of the tank and the
underside of the tank cover. Clean and allow the filters
to dry completely.
NOTE: WET PICK UP ACCESSORIES SHOULD BE
WASHED PERIODICALLY; ESPECIALLY AFTER PICKING
UP WET, STICKY KITCHEN ACCIDENTS. THIS CAN BE
ACCOMPLISHED WITH A WARM SOLUTION OF SOAP
AND WATER.
AUTOMATIC SUCTION
SHUT OFF
54. The vacuum is equipped with an automatic suction
shut-off that operates when picking up liquids. As the
level of the liquid rises in the tank, an internal float rises
until it seats itself against a seal at the intake of the
motor, shutting off suction. When this happens, the
motor will develop a higher than normal pitch noise and
the suction is drastically reduced. If this occurs, turn
unit off immediately. Failure to turn unit off after float
rises and shuts off suction will result in extensive
PAGE 10
44. For vacuuming large quantities of liquid use a
foam sleeve (not standard) . A foam sleeve may be
purchased at your local distributor, on the Dynabrade
Inc. website. To use the foam sleeve; follow the
installation instructions in this section.
45. Misting in the exhaust air or dripping of liquid
around the tank cover may occur if the filter becomes
saturated during wet pick up. If this occurs, remove the
filter and allow to dry, or replace with another dry filter.
46. Turn the unit off immediately upon completing a
wet pick up job or when tank is full and ready to be
emptied. When the tank is full, suction will drastically
reduce. Refer to “automatic suction shut off” in this
manual. Raise the hose to drain any excess liquid into
the tank. Follow the “emptying liquid waste” section in
this manual.
Liquid waste may be emptied by removing the tank
cover. To empty, stop the motor and remove the plug
from the wall receptacle. Remove the tank cover and
deposit the liquid waste contents in a suitable drain.
After tank is empty, return the cover to its original
position. To continue use, plug the cord into the wall
receptacle and turn the unit on.