Dyna-Glo BF10DTDG-2 Скачать руководство пользователя страница 4

3

IMPORTANT:

 Read this owner’s manual carefully and completely before trying to assemble, operate, 

or service this heater. Improper use of this heater can cause serious injury or death from burns, fire, 

explosion, electrical shock, and carbon monoxide poisoning.

IMPORTANT SAFETY INFORMATION 

 

 

Installation and repair should be done by a qualified service person. The appliance should be 

inspected before use and at least annually by a professional service person. More frequent 

cleaning may be required due to excessive lint from carpeting, bedding material, etc. It 

is imperative that control compartments, burners and circulating air passageways of the 

appliance be kept clean.

 

 

WARNING:

 Any change to this heater or its controls can be dangerous. 

 

WARNING:

 

Carefully supervise young children when they are in the room with the heater.

 

WARNING: 

Heater becomes very hot when operating. Children and adults should be alerted 

       to the hazard of high surface temperatures and should stay away to avoid burns or clothing 

       ignition Heater will remain hot for a time after shutoff. Allow surfaces to cool before touching. 

 

 

WARNING:

 Make sure any panel, safety screen or guard removed for servicing an appliance   

       is replaced prior to operating the heater
 

WARNING:

 Keep the appliance area clear and free from combustible materials, gasoline, and  

 

other flammable vapors and liquids. 

 

WARNING:

 Do not place clothing or other flammable material on or near the appliance. Never  

 

place any objects on the heater.

       

WARNING:

 Due to high temperatures, locate this appliance out of traffic and away from

       furniture and draperies.
This appliance is intended for supplemental heating.

This appliance can be used with propane or natural gas. It is shipped from the factory adjusted for 

use with propane.

CARBON MONOXIDE POISONING: 

Early signs of carbon monoxide poisoning resemble the flu with 

headaches, dizziness, or nausea. If you have these signs, the heater may not be working properly. Get 

fresh air immediately! Have heater serviced. Some people are more affected by carbon monoxide than 

others. These include pregnant women, people with heart or lung disease, people who are 

anemic, those under the influence of alcohol, and those living in high altitudes.

NATURAL AND PROPANE/LP GAS:

 Natural and Propane/LP gases are odorless. An odor-making 

agent is added to the gas. The odor helps you detect a gas leak. However, the odor added to the gas 

can fade. Gas may be present even though no odor exists. Make certain you read and understand all 

warnings. Keep this manual for reference. It is your guide to operating this heater safely. 

If the heater is being installed in a residential garage, it must be secured firmly to the 

wall, a minimum of 18 in. (457mm) above the floor. The heater must be located so that it 

is protected against any possibility of damage by a moving vehicle, etc.

Raising the heater will reduce BUT NOT eliminate the possibility of lighting the vapor of any

flammable liquids which may be improperly stored or accidentally spilled. If the smell of 

gasoline is present, do not operate this heater until the area has been properly ventilated.

WARNING:

Содержание BF10DTDG-2































Отзывы: