dymax 40077 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 28

background image

19

Dymax BlueWave® 75 User Guide

Troubleshooting

WARNING!

Only qualified maintenance personnel should attempt the following procedures.

AVERTISSEMENT!

Seulement personnel d’entretien diplomé devrais essayer les procedures suivant.

Table 1. Troubleshooting Chart for

BlueWave 75

Problem

Possible Cause

Testing

Corrective Action

Bulb will not
ignite

or

Change Bulb
Light is on

Improper connections

Visually inspect all input/output
connections (i.e. Power Cord,
Bulb).

Secure all connections.

Bulb is beyond useful
life of 2,000 hours

Replace with a new Bulb/Reflector
Assembly. Reset Bulb Hour Meter
and re-test unit.

Replace Bulb/Reflector Assembly if
required. Typical Bulb life is 2,000
hours.

Main line Fuse blown
(nothing in unit
operates)

Remove Fuse from Power
Receptacle and check with an
Ohmmeter.

Replace Fuse, if defective.

Low output
intensity

or

System fails
to cure
adhesive in
allotted time

Bulb beyond useful life

Use a Radiometer to measure
output intensity (Dymax ACCU-

CAL™ 50 or equivalent)

.

Replace Bulb/Reflector Assembly if
beyond useful life.

Transmission loss in
Lightguide too great

Compare Lightguide output against
new Lightguide (or use the Dymax
Lightguide Simulator) to determine
transmission loss.

Inspect and clean guide ends, and
eliminate tight bends.
Replace Lightguide.

Contaminants on
Lightguide

Visually examine ends of
Lightguide for contaminants.

Clean with isopropyl alcohol or
equivalent. Heavy deposits on
liquid Lightguides may be carefully
removed using a razor blade.
Replace the Lightguide if it cannot
be cleaned.

Bulb/Reflector
Assembly not installed
properly

Visually check to make sure the
Bulb/Reflector Assembly is seated
flush in the Bulb Mount Assembly
(any error in installation could
cause a low output)

Properly install Bulb/Reflector
Assembly, see page 17.

«
...
17
18
19
20
21
...
»

Содержание 40077





























Отзывы:

Нет отзывов

Похожие инструкции для 40077

Бренд: Habegger Страницы: 2

Бренд: MagicRadar Страницы: 98

BrewZilla 100L - Gen 4

Бренд: KegLand Страницы: 48

Бренд: Aiwa Страницы: 30

Power2 S-MIG 100

Бренд: STAMOS Страницы: 33

Бренд: UDP Technology Страницы: 17

Бренд: MartinLogan Страницы: 12

NVL Vista 05 Series

Бренд: Braun Страницы: 30

Бренд: Bauhn Страницы: 28

Бренд: Technics Страницы: 24

SG21CD7484UQ-A80

Бренд: Lorex Страницы: 35

Бренд: Sonoro Страницы: 336

Бренд: jablotron Страницы: 16

Бренд: Salda Страницы: 28

Бренд: Insignia Страницы: 2

Бренд: Rotary Страницы: 12

Бренд: Rehasense Страницы: 6

Бренд: STAMOS Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды