• Be sure the trigger is not adjusted to the
point where it is too sensitive and may
cause accidental discharge of the marker.
• Removing the trigger spring will cause
premature wear on the microswitch,
resulting in failure.
• Be sure you do not pinch the wires
between the frame and body if
reattaching the frame to the body.
W A R N I N G
ADJUSTING YOUR TRIGGER
The trigger’s forward travel, over travel and spring tension are fully adjustable so that the user can fine-tune the
trigger to his or her exact liking. You do not need to remove the frame from the gun in order to adjust the trigger
pull.
• There are two adjustment screws located on the right side of the Ultralite frame (see figure 1) and one
adjustment screw behind the trigger. The two screws on the side of the frame adjust the travel of the trigger.
The one located behind the trigger is used to change the tension of the trigger spring.
TO ADJUST TRIGGER TRAVEL
• Use a 5/64” Allen wrench to make the desired adjustments.
• The screw toward the front of the trigger (#1 in figure 1) controls the forward travel. Screwing it in will
shorten the trigger’s length of pull.
Note: If this screw is adjusted too far, the switch will be held down at all times and the marker will not fire.
• The screw toward the rear of the trigger (#2 in figure 1) controls the over travel. By turning this screw you
can adjust how far the trigger will travel after it reaches the firing point.
Note: If this screw is adjusted too far, the trigger will not be allowed to travel far enough to depress the
switch and fire the marker.
TO ADJUST SPRING TENSION
• Use a 5/64” Allen wrench to make the desired adjustment. The adjustment is made by pushing the allen key
through a hole in the trigger.
• To make the trigger pull stiffer, turn the allen key clockwise or in.
• To make the trigger pull lighter, turn the allen key counterclockwise or out.
INTEGRATED LOCKING DOVETAIL FEATURE
The UltraLite frame comes equipped with an integrated locking dovetail. There is a locking screw located on the
bottom right side of the UltraLite frame. It can be accessed with a 1/8" allen key through a hole in the grips panels.
To unlock a part attached to the dovetail of the frame, turn the locking screw counter clockwise one full turn and
slide part off the rail. To attach a part to the rail, slide the part on and turn the locking screw clockwise until part is
firmly locked in place.
REMOVING ULTRALITE FRAME FROM THE DM6
If there is ever need to remove the Ultralite frame from the DM6 make sure to follow these steps.
• Remove three grip panel screws with a 3/32" allen wrench from the right side of UltraLite frame
• Disconnect the solenoid wire and the eye wire from their sockets by gently pulling them out
• Using a 3/32" allen key, turn the front frame screw counterclockwise one full turn
• Finally, turn out the back frame screw and slide the frame back and down until it comes off the DM6
To connect the frame follow above steps in reverse order.
NOTE: BE SURE THAT THE FRAME AND TRIGGER ASSEMBLY ARE KEPT CLEAN. IF THERE IS EXCESS DIRT OR
PAINT BUILD UP AROUND THE TRIGGER, THE TRIGGER WILL NO LONGER MOVE FREELY. IN ADDITION, PAINT
AND DIRT CAN CAUSE THE MICROSWITCH TO NOT FUNCTION PROPERLY OR FAIL. BE SURE YOU DO NOT PINCH
THE WIRES BETWEEN THE FRAME AND THE BODY WHEN REATTACHING THE FRAME AND BODY.
U LT R ALI T E F R AM E
1
Adjustable Feed Neck
2
On/Off Knob
3
Ball Detent
4
Eye Cover
5
Self Cleaning Eye Lens
6
Hyper
2
7
On/Off Retaining Screw
8
“ACE” Eye
9
Solenoid
10
Front Frame Screw
11
Ultralite 45 Frame
12
Rear Frame Screw
13
LPR Retaining Screw
14
LPR
15
LPR Cap
16
Fuse Bolt
17
DM6 Body
P A R T S L I S T
14
15
1
2
FIGURE 1
1
2
3
4
6
8
13
9
7
10
12
14
15
16
11
7
17
5
