- 3 -
M965703 1.0 (5/17)
4
5
6
WATER SUPPLY CONNECTIONS
MAKE WATER SUPPLY CONNECTIONS
NOTE: FLEXIBLE SUPPLIES OR BULL-NOSE RISERS
MUST BE PURCHASED SEPARATELY.
• Connect water supply to VALVE BODIES
(1)
with 1/2" (13 mm) IPS
FLEXIBLE SUPPLIES
(3)
or 3/8" (10 mm) O.D. BULL-NOSE RISERS
(4)
.
Use wrench to tighten connections.
• Do not over tighten. Be careful not to kink copper supply when
bending. Use tubing cutter to cut to proper length.
• Remove AERATOR
(3)
from faucet.
• With HANDLES
(1)
in OFF position, turn on WATER SUPPLIES
(2)
and check all connections for leaks.
Operate both HANDLES to flush water lines thoroughly.
• Operate Lift Rod
(5)
and ll lavatory with water. Check that DRAIN
STOPPER
(4)
makes a good seal and retains water in lavatory.
Adjust stopper height by repositioning Lift Rod
(5)
and
tightening SET SCREW (6).
• Release DRAIN STOPPER
(4)
and check all drain connections and
“P” trap for leaks. Tighten if necessary.
• Replace AERATOR
(3)
.
INSTALL POP-UP DRAIN
FIG. 4a
• A FOAM SEAL
(1)
is installed on underside of FLANGE
(2)
.
(Plumbers Putty may be used in place of FOAM SEAL
(1)
if desired.)
• Drop FLANGE
(2)
into LAVATORY DRAIN
(3)
. From below assemble
RUBBER GASKET
(4)
, PLASTIC WASHER
(5)
and LOCK NUT
(6)
onto DRAIN FLANGE
(2)
. Do not tighten fully.
FIG. 4b
• Inspect inside DRAIN BODY
(7)
that SEAL
(8)
is installed. Thread
DRAIN BODY
(7)
tight against FLANGE
(2)
to make a water tight seal.
• The PIVOT ROD OPENING
(9)
in DRAIN BODY
(7)
should face the rear
of the lavatory. Tighten LOCK NUT
(6)
on FLANGE
(2)
to make a water
tight connection with channel locks. Do not over tighten.
• Apply sealant or Teon tape to threads of TAILPIECE
(10)
and
thread into DRAIN BODY
(7)
making a water tight seal.
FIG. 4c
• Assemble PIVOT ROD
(11)
, WASHER
(20)
and PIVOT NUT
(12)
as shown.
Install CONCAVE WASHER (
19)
into PIVOT ROD OPENING
(9)
if not
reinstalled. Hand tighten PIVOT NUT
(12)
. Drop STOPPER
(13)
into drain.
(To vandal proof drain rotate STOPPER (13) so PIVOT ROD (11) goes
through EYE (14) of STOPPER (13)
. Make connection to “P” TRAP.
• Assemble POP-UP SWIVEL
(15)
to PIVOT ROD
(11)
but do not tighten. Drop
POP-UP ROD
(16)
through other hole in POP-UP SWIVEL
(15)
and tighten SET SCREW
(17)
.
• Adjust STOPPER
(13)
height by repositioning POP-UP ROD
(16)
in SWIVEL
(15)
and tightening SET SCREW
(18)
.
APPLY SEALANT
OR TEFLON TAPE
FIG. 4c
FIG. 4a
FIG. 4b
1
4
3
2
5
6
7
8
6
9
2
10
9
7
6
12
19
16
15
17
18
2
10
14
13
11
20
3
1
4
FERRULE
COUPLING NUT
2
2
1
4
5
6
3
