- 2 -
M965703 1.0 (5/17)
1
2
3
HOSE ASSEMBLY
• If HANDLES
(1 & 2)
and HANDLE BASE
(3)
are installed on
VALVE BODIES
(4)
they must be removed to install VALVE BODIES
(4)
from under lavatory or mounting surface.
• To remove CROSS HANDLE
(1)
; Pull-out INDEX CAP
(5)
and
remove HANDLE SCREW
(6)
. Pull off CROSS HANDLE
(1)
and
unthread HANDLE BASE
(3
).
• To remove LEVER HANDLES
(2)
; loosen SET SCREW
(7)
with
Hex Wrench provided with faucet. Pull LEVER HANDLE
(2)
off and
unthread HANDLE BASE
(3)
.
• Thread LOCKNUT
(8)
to bottom of VALVE BODY
(4)
. Make sure FIBER
WASHER
(9)
and RUBBER WASHER
(10)
are installed. Insert VALVE BODY
(4)
through mounting hole from underside of SINK or mounting surface.
Note: Maximum mounting thickness is 1-1/4" (32 mm)
• Thread LOCKNUT
(8)
to bottom of VALVE BODY
(4)
. Make sure
FIBER WASHER
(9)
and RUBBER WASHER
(10)
are installed.
Insert VALVE BODY
(4)
through mounting hole from underside of
SINK or mounting surface.
• Thread HANDLE BASE
(3)
until snug against internal stop. Set VALVE
BODIES
(4)
so that their outlets are facing toward SPOUT TEE
(11)
and
then tighten LOCKNUT
(8)
using wrench.
• Tighten COUPLING NUT
(12)
on SUPPLY HOSE
(14)
to OUTLET
(13)
making water tight connection.
Important: Loop SUPPLY HOSES (14) as shown so they do not kink.
INSTALL HANDLES
•
FOR LEVER HANDLES:
Install FRICTION WASHER
(15)
onto base of LEVER HANDLE
(2)
. With VALVE in off position
align LEVER HANDLE
(2)
as shown. Install LEVER HANDLE
(2)
onto VALVE STEM
(16)
and tighten SET SCREW
(7)
with
HEX WRENCH supplied.
•
FOR CROSS HANDLES:
With VALVE in off position align CROSS HANDLE
(1)
as shown. Install CROSS HANDLE
(1)
onto
VALVE STEM
(16)
and tighten HANDLE SCREW
(6)
. Insert HOT INDEX
(5)
into left CROSS HANDLE and COLD INDEX
(17)
into right CROSS HANDLE.
• Insert SPOUT SHANK
(1)
through
center hole of sink or mounting
surface. Make sure RUBBER
WASHER
(2)
is seated into groove
in SPOUT ESCUTCHEON BASE
(3)
.
• Assemble RUBBER WASHER
(4)
,
BRASS WASHER
(5)
and
LOCKNUT
(6)
onto threads of SPOUT
SHANK
(1)
from underside of lavatory
or mounting surface.
• Align SPOUT
(7)
and tighten
LOCKNUT
(6)
. Insert LIFT ROD
(8)
through SPOUT
(7)
.
SPOUT ASSEMBLY
TEE ASSEMBLY
CAUTION
Turn off hot and cold water
supplies before beginning.
• Thread TEE BODY
(1)
COUPLING NUT
(2)
to SPOUT SHANK
(3)
.
1
2
3
7
8
GROOVE
4
6
5
1
3
2
5
6
1
3
2
8
4
12
13
14
9
11
10
7
HEX WENCH,
SUPPLIED
15
COLD
HOT
1-1/4'' MAX.
