PLUG-N-PLAY MODULES
SLMOD5PD
SLMOD8RI
SLMOD8RK
SLMOD8RY
YAESU
FT-920
FT-1000MP
FT-1000MPMKV
FT-1000MPMKV Field
FT-2000
FTDX-5000/D/MP
FTDX-9000/D/MP
TEN-TEC
Argonaut V
Jupiter
Omni VII
Pegasus
Eagle**
Orion**
Orion II**
**These radio's use an
8-pin DIN radio cable,
but the jumper settings
required are the same as
those used by the 5-pin
DIN cable.
ICOM
IC-1201/1271/1275
IC-22U/25/27/28
IC-228/229/251AE
IC-255/260/271/290
IC-2400/2500
IC-37A/38A/375
IC-3200/3210/3220
IC-45/47/48
IC-471/475/490
IC-505/551/560/575
IC-707/718/720/725/726
IC-728/729/730/735
IC-736/737/738/740/745
IC-746/746PRO
IC-756/756PRO
IC-756PROII/PROIII
IC-7400/7700/7800
IC-751/761/765/775/781
IC-820H/901 /910
PWR / SPKR Jumper Settings - To
maintain compatibility with as
many radios as possible, this
jumper module has two small
jumpers that can be set to enable
Power and Speaker Audio.
PWR - This jumper is *NOT* used
with the SignaLink USB, but can
be installed to power the older
SignaLink SL-1 or SL-1+ model
from your radio if there is
sufficient power available on Pin
#2 of the Mic connector (check
your radio manual).
SPKR - This jumper should only
be installed if your radio has
Speaker Audio on Pin #8 of the
Mic jack (check your radio
manual). If Speaker Audio isn't
available, then you'll need to
connect an audio cable between the
radio and the SignaLink as
described in the SignaLink
Installation Manual.
KENWOOD
TM-201/211/221/231
TM-241/2530/2550
TM-2570
TM-321/331/3530/401
TM-421/431/441/521
TM-531/541/621/631
TM-701/721/731
TR-50/751/851
TS-50/60/140/430/440
TS-450/570/660/670
TS-680/690/701/711
TS-780/790/811/850
TS-870/930/940/950
TS-2000
TW-4000/4100
ALINCO
ALD-24T
ALR-22T/22HT/72T
DR-110T/112T
DR-130T/135E/135T
DR-150/235T
DR-430T/435E/435T
DR-510T/570T
DR-590T/592T/599T
DR-600T /610E/610T
DR-620E/620T
DX-70T /70TH/70EH
DX-77
PWR / SPKR Jumper Settings - To
maintain compatibility with as many
radios as possible, this jumper module
has two small jumpers that can be set to
enable Power and Speaker Audio.
PWR - This jumper is *NOT* used with
the SignaLink USB, but can be installed
to power the older SignaLink SL-1 or
SL-1+ model from your radio if there is
sufficient power available on Pin #5 of
the Mic connector (check your radio
manual).
SPKR - This jumper should only be
installed if your radio has Speaker Audio
on Pin #6 of the Mic jack (check your
radio manual). If Speaker Audio isn't
available, then you'll need to connect an
audio cable between the radio and the
SignaLink as described in the SignaLink
Installation Manual.
YAESU
FT-107/107M
FT-736/736R
FT-747/757
FT-757GX
FT-767GX
FT-840/847
FT-890
FT-920/950
FT-980/990
FT-1000/1000D
FT-1000MP
FT-2000
FT-2200
FT-dx5000
FT-5100
G1 / G2 Jumper Settings -
To maintain compatibility
with as many radios as
possible, this jumper module
has two small jumpers that
can be set to provide
additional Ground ("G")
connections needed by some
radios (see below). These
two jumpers should be
installed as follows for the
following radios only. Do
*NOT* install either jumper
if your radio isn't listed
below:
Both jumpers "G1" and "G2"
should be installed for the
FT-890, FT-980, FT-990,
FT-1000 and the FT-1000D.
Only jumper "G1" should be
installed for the FT-847, FT-
920, FT-950, FT-1000MP,
and FTdx5000.
