- 35 -
3M Temflex™ 2155 Rubber Splicing Tape
Conformable self-fusing rubber electrical insulating tape. It is designed for low voltage electrical insulating and moisture
sealing applications. For outdoor use, it should be protected from UV deterioration with an overwrap of
Scotch
®
Super
33+.
Scotch
®
Super 33+
Highly conformable super stretchy tape for all weather applications. This tape provides flexibility and easy handling for all
around performance. It also combines PVC backing with excellent electrical insulating properties to provide primary
electrical insulation for splices up to 600V and protective jacketing. Both tape products are available from DX Engineering.
DXE-VMN-1 - Vertical Antenna Matching Network
The
DXE-VMN-1
Vertical Antenna Matching Network is custom designed for use with base-fed quarter wave resonant vertical
antenna systems. In some vertical antenna installations with excellent radial systems, achieving the best SWR on a
resonant vertical for 80 meters may be difficult without some means of adjusting feedpoint impedance. The
DXE-
VMN-1
allows easy adjustment for lowest SWR. The
DXE-VMN-1
Vertical Antenna Matching Network will aid in
tuning a low impedance antenna to the minimum SWR in the customer selected portion of the 80 meter band. The #12
AWG coil wire is tin-nickel plated for high power handling, corrosion resistance, ease of soldering and long term
reliability.
As an added benefit, the
DXE-VMN-1
will also act as a static bleed for your resonant vertical antenna in
areas where precipitation or snow static is present. The Vertical Matching Network may be installed between ground
and the feedpoint of any quarter wave base-fed vertical antenna - including mobile antennas. It
CANNOT
be used on
non-resonant antenna such as a 43 foot vertical.
Technical Support
If you have questions about this product, or if you experience difficulties during the installation,
contact DX Engineering at (330) 572-3200. You can also e-mail us at:
For best service, please take a few minutes to review this manual before you call.
Warranty
All products manufactured by DX Engineering are warranted to be free from defects in material and workmanship for a period of one
(1) year from date of shipment. DX Engineering’s sole obligation under these warranties shall be to issue credit, repair or replace any
item or part thereof which is proved to be other than as warranted; no allowance shall be made for any labor charges of Buyer for
replacement of parts, adjustment or repairs, or any other work, unless such charges are authorized in advance by DX Engineering. If
DX Engineering’s products are claimed to be defective in material or workmanship, DX Engineering shall, upon prompt notice
thereof, issue shipping instructions for return to DX Engineering (transportation-charges prepaid by Buyer). Every such claim for
breach of these warranties shall be deemed to be waived by Buyer unless made in writing. The above warranties shall not extend to
any products or parts thereof which have been subjected to any misuse or neglect, damaged by accident, rendered defective by reason
of improper installation, damaged from severe weather including floods, or abnormal environmental conditions such as prolonged
exposure to corrosives or power surges, or by the performance of repairs or alterations outside of our plant, and shall not apply to any
goods or parts thereof furnished by Buyer or acquired from others at Buyer’s specifications. In addition, DX Engineering’s warranties
do not extend to other equipment and parts manufactured by others except to the extent of the original manufacturer’s warranty to
DX Engineering. The obligations under the foregoing warranties are limited to the precise terms thereof. These warranties provide
exclusive remedies, expressly in lieu of all other remedies including claims for special or consequential damages. SELLER
NEITHER MAKES NOR ASSUMES ANY OTHER WARRANTY WHATSOEVER, WHETHER EXPRESS, STATUTORY, OR
IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS, AND NO PERSON IS AUTHORIZED TO
ASSUME FOR DX ENGINEERING ANY OBLIGATION OR LIABILITY NOT STRICTLY IN ACCORDANCE WITH THE
FOREGOING.
©DX Engineering 2021
DX Engineering
®
, DXE
®
, DX Engineering, Inc.
®
, Hot Rodz
®
, Maxi-Core
®
, DX Engineering THUNDERBOLT
®
, DX Engineering
Yagi Mechanical
®
, EZ-BUILD
®
, TELREX
®
, Gorilla Grip
®
Stainless Steel Boom Clamps, Butternut
®
, SkyHawk™, SkyLark™,
SecureMount™, OMNI-
TILT
™, RF-PRO-1B
®
, AFHD-4
®
are trademarks of PDS Electronics, Inc. No license to use or reproduce
any of these trademarks or other trademarks is given or implied. All other brands and product names are the trademarks of their
respective owners.
Specifications subject to change without notice.
