background image

24 

Technical Support

 

 

 
If you have questions about this product, or if you experience difficulties during the installation, 
contact DX Engineering at (330) 572-3200.  You can also e-mail us at:       

 
 

[email protected]

 

 

 

For best service, please take a few minutes to review this manual before you call. 

 

 
 
Warranty 

 

All products manufactured by DX Engineering are warranted to be free from defects in material and workmanship for a 
period of one (1) year from date of shipment. DX Engineering’s sole obligation under these warranties shall be to issue 
credit, repair or replace any item or part thereof which is proved to be other than as warranted; no allowance shall be 
made  for  any  labor  charges  of  Buyer  for  replacement  of  parts,  adjustment  or  repairs,  or  any  other  work,  unless  such 
charges are authorized in advance by DX Engineering.  If DX Engineering’s products are claimed to be defective in 
material or workmanship, DX  Engineering  shall, upon prompt  notice thereof,  issue  shipping  instructions for return to 
DX  Engineering  (transportation-charges  prepaid  by  Buyer).  Every  such  claim  for  breach  of  these  warranties  shall  be 
deemed to be waived by Buyer unless made in writing. The above warranties shall not extend to any products or parts 
thereof  which  have  been  subjected  to  any  misuse  or  neglect,  damaged  by  accident,  rendered  defective  by  reason  of 
improper  installation,  damaged  from  severe  weather  including  floods,  or  abnormal  environmental  conditions  such  as 
prolonged exposure to corrosives or power surges, or by the performance of repairs or alterations outside of our plant, 
and shall not apply to any goods or parts thereof furnished by Buyer or acquired from others at Buyer’s specifications. 
In addition, DX Engineering’s warranties do not extend to other equipment and parts manufactured by others except to 
the extent of the original manufacturer’s warranty to DX Engineering.  The obligations under the foregoing warranties 
are  limited  to  the  precise  terms  thereof.  These  warranties  provide  exclusive  remedies,  expressly  in  lieu  of  all  other 
remedies including claims for special or consequential damages. SELLER NEITHER MAKES NOR ASSUMES ANY 
OTHER  WARRANTY  WHATSOEVER,  WHETHER  EXPRESS,  STATUTORY,  OR  IMPLIED,  INCLUDING 
WARRANTIES  OF  MERCHANTABILITY  AND  FITNESS,  AND  NO  PERSON  IS  AUTHORIZED  TO  ASSUME 
FOR DX ENGINEERING ANY OBLIGATION OR  LIABILITY NOT STRICTLY IN ACCORDANCE WITH THE 
FOREGOING. 
 
©DX Engineering 2017 
 
DX Engineering

®

, DXE

®

,  DX  Engineering, Inc.

®

,  Hot  Rodz

®

,  Maxi-Core

®

, DX Engineering THUNDERBOLT

®

,  DX 

Engineering  Yagi  Mechanical

®

,  EZ-BUILD

®

,  TELREX

®

,  Gorilla  Grip

®

  Stainless  Steel  Boom  Clamps,  Butternut

®

SkyHawk™, SkyLark™, SecureMount™, OMNI-

TILT

™, RF-PRO-1B

®

, AFHD-4

®

 are trademarks of PDS Electronics, 

Inc. No license to use or reproduce any of these trademarks or other trademarks is given or implied. All other brands 
and product names are the trademarks of their respective owners. 
 
 
Specifications subject to change without notice. 

 

 
 
 

Содержание DXE-RFS-SYS-3P

























Отзывы: