DWT KGS12-210, Оригинальное руководство пользователя

Страница: 15 / 80

15
English
• Slightly press handle 11 .
• Pull lock 29 all the way out. For KGS16-255 turn
lock 29 , 90° in any direction and slightly press to fix in
this position.
• Lift the body up smoothly.
• To position the power tool for carriage, do the indi-
cated operations in a reverse order.
Dust bag mounting / dismounting (see fig. 3)
Before operation put dust bag 33 on dust removing
coupler 4 (see fig.3). Dump and clean dust bag 33 in
due time.
Turn-over protection bracket mounting / dismount-
ing (see fig. 4)
If you are planning to operate the power tool without
fixing it to the worktable (using bolts or cramps), you
should mount bracket
30
and fix it using screw
35
be-
fore starting any work (see fig.4).
Extension bracket mounting / dismounting (see fig. 5)
[KGS16-255]
If you are planning to cut long blanks, you should
mount extension brackets 26 , adjust them properly
(depending on the blank length) and fix them using
screws
36
(see fig. 5).
Cramp mounting / dismounting (see fig. 6)
In order to fix the blanks properly, mount cramp 22 and
fix it using butterfly screw 28 (see fig. 6). Adjust cramp 22
depending on the length and thickness of the blank.
Turntable lock mounting / dismounting (see fig. 7)
[KGS16-255]
Lock 19 is intended for setting and fixing the rotation
angle of table 16 . Mount / dismount lock 19 as illus-
trated in figure 7.
Installation / replacement of the batteries for the
kerf indicating laser (see fig. 8-9)
• Take off cover 37 (see fig. 8-9).
• Install / replace batteries
32
(AA type).
Caution:
during installation of batteries 32, observe correct
polarity.
• Place cover 37 back.
Replacement of the saw blade (see fig. 10-11)
After prolonged operation, the saw blade
can become very hot, remove it using
gloves. This will also reduce the risk of
injury by the cutting edge.
• Lift the body to the uppermost position.
• Press blocking lever 10 to the left with one hand (see
fig. 21) and move sliding guard cover 13 to the uppermost
position with the other hand as shown in figures 10-11.
• Loosen fixing screw 39 and turn plate 38 back (see
fig. 10-11).
• Press spindle lock 24 and manually turn saw blade 5
in order to immobilize it. While pressing spindle lock 24 ,
turn off bolt
6
with wrench
34
.
Caution: bolt 6 is left-
hand threaded.
• Take off external flange 7 , saw blade 5 , mounting ring 40 .
• Clean the fixing elements with a soft brush and
put mounting ring 40 , new saw blade 5 and external
flange 7 on the spindle.
• While pressing spindle lock 24 , tighten bolt 6 with
wrench
34
. Release spindle lock
24
.
• Return plate 38 to its original position and tighten
fixing screw 39 .
• Move sliding guard cover 13 to its original position.
• Ensure that saw blade 5 does not touch any power
tool elements and can rotate freely.
Adjustment of the cutting depth (see fig. 12-13)
Using bolt 41 and lock-nut 42 adjust the cutting depth
so that saw blade
5
goes into the slit of insert
17
by
max. 5 mm in its lowest position.
• Loosen lock-nut 42 .
• Adjust the cutting depth by turning bolt 41 in or out.
• Tighten lock-nut 42 .
Vertical alignment of the body and adjustment of
the 45° tilt (see fig. 14-17)
• Position the body for carriage.
• Loosen lock lever 1 and set the body tilt
angle (90° or 45°). Tighten lock lever
1
.
• Place the sides of an alignment setsquare 90° or 45°
(depending on the angle to align) to the surface of saw
blade 5 and turntable 16 . If the setsquare sides join
the surfaces of saw blade 5 and table 16 tightly, then
alignment is not needed, otherwise you have to do it.
Use bolt 43 and lock-nut 44 for vertical align -
ment of the body (see fig. 14, 16).
Use bolt 45 and lock-nut 46 for adjustment
of the body tilt angle 45° (see fig. 15, 17).
• Loosen lock lever 1 .
• Loosen the lock-nut.
• Turning the adjustment bolt in or out, makethe sides
of the 90° or 45° setsquare (depending on the angle
to adjust) join the surfacesof saw blade 5 and table 16
tightly.
• Tighten the lock-nut.
• Loosen screw 48 and place indicator 47 to the 0° (on
scale 2 ) or 45° position (depending on the angle to ad-
just), then tighten screw 48 .
Retaining bar alignment (see fig. 18-19)
• Set the 0° horizontal cutting angle (the procedure is
described below).
• Position the body for carriage.
• Place the sides of an alignment setsquare 90° to the
surface of saw blade
5
and re taining bar
14
. If the
setsquare sides join the surfaces of saw blade 5 and
retaining bar 14 tightly, then alignment is not needed,
otherwise you have to do it.
• Loosen retainer bolts 27 , and by moving retaining
bar 14 make the sides of the 90° setsquare join the
surfaces of saw blade 5 and retaining bar 14 tightly.
• Tighten retainer bolts 27 .
Kerf indicating laser alignment (see fig. 20)
Before starting any work, ensure that the kerf indicat-
ing laser is properly aligned.