1st POS.
1. CW direction
2. CCW direction
2nd POS.
SCAN NO.
Selects the scan number to edit. If a selected scan has not
defined, ‘NOT USED’ is displayed in 1st position and
2nd position.
1ST POS. / 2 ND POS.
Set up the 2 position for scan function. If a selected preset is
not defined, ‘UNDEFINED’ will be displayed as shown
below.
SCAN SPEED
Sets the scan speed.
CLEAR SCAN
Deletes the current scan data.
PRESET SETUP
- - - - - - - - - - - - - - - - - - - - - - - - - - -
PRESET NO.
<
EDIT SCENE
>
<
LABEL
>
CLR PRESET
CAM ADJUST
ALARM OUT
BACK
EXIT
1
CANCEL
GENERAL
-
FUNCTION SETUP
- - - - - - - - - - - - - - - - - - - - - - - - - - -
<
PRESET SETUP
>
<
SCAN SETUP
>
<
PATTERN SETUP
>
<
GROUP SETUP
>
<
SCHEDULE SETUP
>
BACK
EXIT
PRESET SETUP
- - - - - - - - - - - - - - - - - - - - - - - - - - -
PRESET NO.
<
EDIT SCENE
>
BACK
EXIT
1
UNDEFINED
EDIT SCENE -PRESET1
- - - - - - - - - - - - - - - - - - - - - - - - - - -
MOVE TO TARGET POSITION
[NEAR:SELECT/FAR:CANCEL]
0/0/x1/E
!
Note: to properly setup a scan for the camera,
be sure to have at least 2 Presets setup..
9
10
12
11
13
15
16
14
OSD MENU
(FOR DW’S VMAX, VMAX480 & VMAX Flex)
OSD MENU
(CONTROL THROUGH THE DVR)
!
Please consult the manual for further instructions on how
to use a computer mouse to operate the OSD Menu
RESERVED PRESETS
PRESET SETUP
PATTERN SETUP
SCAN SETUP
A preset is a pre-defined position for the camera. Setup 127
presets, excluding 95, which is reserved for menu access.
By using the scan function, you can make the camera to move between 2
preset positions repeatedly.
When the scan function runs, the camera moves from the preset assigned
as the 1st point to the preset assigned as the 2nd point in Clockwise
direction. Then the camera moves from the preset assigned as the 2nd
point to the preset assigned as the 1st point in Counterclockwise direction.
In case that the preset assigned as the 1st point is same as the preset
assigned as the 2nd point, the camera turns on its axis by 360° in CW
direction and then it turns on its axis by 360° in CCW direction.
Pattern function is when a camera memorizes the path (mostly
curve path) created by a joystick controller and revives the
path exactly as it memorized for an assigned time.
4 patterns are available and maximum 1000 communication
commands can be stored in a pattern.
FUNCTION SETUP
- - - - - - - - - - - - - - - - - - - - - - - - - - -
<
PRESET SETUP
>
<
SCAN SETUP
>
<
PATTERN SETUP
>
<
GROUP SETUP
>
<
SCHEDULE SETUP
>
BACK
EXIT
PATTERN SETUP
- - - - - - - - - - - - - - - - - - - - - - - - - - -
PATTERN NO.
CLEAR PATTERN
<
EDIT PATTERN
>
BACK
EXIT
1
UNDEFINED
CANCEL
EDIT PATTERN 1
- - - - - - - - - - - - - - - - - - - - - - - - - - -
MOVE TO START POSITION
[NEAR:START/ FAR:CANCEL]
0/0/x1/E
EDIT PATTERN 1
[NEAR:SAVE / FAR:DELETE]
0/0/x1/E
GROUP SETUP
T
he group function allows you to run sequence of presets, pattern,
and/or scans. Maximum 8 group can be stored. Each group can
have max 20 actions.
To setup a group, at leaset 1 preset, 1 scan, 1 pattern must be setup.
FUNCTION SETUP
- - - - - - - - - - - - - - - - - - - - - - - - - - -
<
PRESET SETUP
>
<
SCAN SETUP
>
<
PATTERN SETUP
>
<
GROUP SETUP
>
<
SCHEDULE SETUP
>
BACK
EXIT
GROUP SETUP
- - - - - - - - - - - - - - - - - - - - - - - - - - -
GROUP NO.
CLEAR GROUP
<
EDIT GROUP
>
BACK
EXIT
1
UNDEFINED
CANCEL
EDIT GROUP 1
- - - - - - - - - - - - - - - - - - - - - - - - - - -
NO. ACTION NO. DWELL OPT
- - - - - - - - - - - - - - - - - - - - - - - - - -
1
NONE
2 NONE
3
NONE
4
NONE
5
NONE
- - - - - - - - - - - - - - - - - - - - - - - - - -
SAVE
CANCEL
[NEAR:EDIT ACT]
[FAR :EDIT END]
[ :MOVE CURSOR]
[ : CHANGE VAL.]
EDIT GROUP 1
- - - - - - - - - - - - - - - - - - - - - - - - - - -
NO. ACTION NO. DWELL OPT
- - - - - - - - - - - - - - - - - - - - - - - - - -
1
NONE
2 NONE
3
NONE
4
NONE
5
NONE
- - - - - - - - - - - - - - - - - - - - - - - - - -
SAVE
CANCEL
SCHEDULE SETUP
The schedule function allows running an appropriate function
like preset, scan, pattern, group, home move at designated
day and time.
To setup a schedule, at leaset 1 Preset, 1 scan, 1 pattern, and 1
group should be setup.
FUNCTION SETUP
- - - - - - - - - - - - - - - - - - - - - - - - - - -
<
PRESET SETUP
>
<
SCAN SETUP
>
<
PATTERN SETUP
>
<
GROUP SETUP
>
<
SCHEDULE SETUP
>
BACK
EXIT
SCHEDULE SETUP
- - - - - - - - - - - - - - - - - - - - - - - - - - -
MASTER ENABLE OFF
DAY TIME ACT NO ON
1
UNDEFINED
2 UNDEFINED
3
UNDEFINED
4
UNDEFINED
5
UNDEFINED
6
UNDEFINED
7 UNDEFINED
BACK
SCHEDULE SETUP
- - - - - - - - - - - - - - - - - - - - - - - - - - -
MASTER ENABLE OFF
DAY TIME ACT NO ON
1
ALL
00:00 HOM OFF
2 UNDEFINED
3
UNDEFINED
4
UNDEFINED
5
UNDEFINED
6
UNDEFINED
7 UNDEFINED
BACK
SCHEDULE SETUP
- - - - - - - - - - - - - - - - - - - - - - - - - - -
MASTER ENABLE ON
DAY TIME ACT NO ON
1
MON 0
1
:20 HOM ON
2 WED 07:00 PRS
1
2 ON
3
THU
11
:40 SCN
3
ON
4
ALL
1
2:00 SCN
1
ON
5
UNDEFINED
6
UNDEFINED
7 UNDEFINED
BACK
>
>
>
SCAN SETUP
- - - - - - - - - - - - - - - - - - - - - - - - - - -
SCAN NO.
1
ST POS.
2ND POS.
SCAN SPEED
1
PRESET
1
NOT USED
30
/SEC
UNDEFINED
SCAN SETUP
- - - - - - - - - - - - - - - - - - - - - - - - - - -
SCAN NO.
1
ST POS.
2ND POS.
SCAN SPEED
CLEAR SCAN
BACK
EXIT
1
NOT USED
NOT USED
30
/SEC
CANCEL
FUNCTION SETUP
- - - - - - - - - - - - - - - - - - - - - - - - - - -
<
PRESET SETUP
>
<
SCAN SETUP
>
<
PATTERN SETUP
>
<
GROUP SETUP
>
<
SCHEDULE SETUP
>
BACK
EXIT
2
1
3
4
4
3
2
1
2
1
3
4
4
3
2
1
In the Root Menu,
go to Function Setup> Pattern Setup
By using joystick, move the camera
to the start position with appropriate
zoom. Using the mouse’s wheel,
scroll near to save and start recording,
or far to cancel all changes.
Move the camera using the Joystick controller
or the computer mouse in the desired pattern.
The total memory size is displayed in the form
of a bar. Using the mouse’s wheel, scroll bear to save
patterm, or scroll far to cancel all changes.
Select the pattern number you wish to setup.
If a selected pattern is not defined, ‘UNDEFINED’
will be displayed as shown.
In the Root Menu,
go to Function Setup> Group Setup
Select the Group you wish to modify. If a group
is not defined, ‘UNDEFINED’ will be displayed
as shown.
Select the first action in the group.
Click with the mouse on the right side
of the screen to enter edit mode.
Using the mouse, click on the top and bottom of the
screen to scrol down the options. Select from
Preset, Pattern, Scan. Click on the right side of the
screen to save selection and move to the next tab to
the right.
Using the mouse, continue editing the desired
information. Enter the action’s number, Dwell
time between each action, and the numebr of
repetitions under OPT.
[ :MOVE CURSOR]
[ : CHANGE VAL.]
EDIT GROUP 1
- - - - - - - - - - - - - - - - - - - - - - - - - - -
NO. ACTION NO. DWELL OPT
- - - - - - - - - - - - - - - - - - - - - - - - - -
1
PATTERN
1
00:0
3
1
2 NONE
3
NONE
4
NONE
5
NONE
- - - - - - - - - - - - - - - - - - - - - - - - - -
SAVE
CANCEL
When you finish setting up an ACTION,
press Near or Enter key to one-upper-level
menu. Move to the next action and repeat setup
as necessary. When you have completed entering
all desired actions, scrol near to save changes,
or far to cancel all changes.
EDIT GROUP 1
- - - - - - - - - - - - - - - - - - - - - - - - - - -
NO. ACTION NO. DWELL OPT
- - - - - - - - - - - - - - - - - - - - - - - - - -
1
PATTERN
1
00:0
3
1
2 NONE
3
NONE
4
NONE
5
NONE
- - - - - - - - - - - - - - - - - - - - - - - - - -
SAVE
CANCEL
[NEAR:EDIT ACT]
[FAR :EDIT END]
In the Root Menu,
go to Function Setup> Schedule Setup
Select the schedule you wish to modify, and using the
mouse’s wheel, scroll near to enter Edit mode.
Select the days of the week you wish
to set for this schedule. Select from
All, WKD (Every day except Saturday
and Sunday), or Sun~Sat. When you are
done, click on the right corner of the screen
to move to the next edit section.
Continue to edit the time of the day, the act you wish
to run at that time (home, preset, pattern, scan, group),
select the act no for a specific action. When you are
complete, to enable the schedule select ON. Using
the mouse’s wheel, scroll near to save changes or far
to cancel.
To enable the camera to start running the schedules,
make sure the specific schedule is enabled, and
also MASTER ENABLE on the top of the screen is ON.
95
Enters Into OSD Menu
ON
131~134
Pattern Function 1 ~ 4
ON
141~148
Scan Function 1 ~ 8
ON
151~158
Group Function 1 ~ 8
ON
161~164
Relay 1~ 4 Output
OFF
Set key +
Relay 1~ 4 Output
ON
161~164
165
Auto Calibration
ON
166
Auto Calibration
OFF
167
Zoom Proportional Jog
ON
Set key +
Zoom Proportional Jog
OFF
167
170
BLC Mode
OFF
171
BLC Mode
HIGH
174
Camera Focus Mode
AUTO
175
Camera Focus Mode
MANUAL
176
Camera Focus Mode
SEMI-AUTO
177
Day & Night Mode
AUTO
178
Day & Night Mode
NIGHT
179
Day & Night Mode
DAY
190
OSD Display Mode
AUTO (
except privacy mask
)
191
OSD Display mMode
OFF (
except privacy mask
)
192
OSD Display Mode
ON (
except privacy mask
)
193
All Privacy Mask display
OFF
194
All PrivacyMask display
ON
200
Digital zoom
ON
201
Digital zoom
OFF
TEL: (866) 446-3595
www.Digital-Watchdog.com / [email protected]
Technical Support Hours: Monday-Friday 8:30AM to 8:00PM EST
Select Full Screen view on the selected PTZ camera
Right-Click the screen & Select ‘PTZ’
Le
ft
Up
Down
Right
Preset 95
Preset 95 is reserved for starting the camera’s OSD menu.
For a complete list of all the reserved presets, see the PTZ12X’s
complete manual or page 19.
Accessing the OSD Menu
1
2
3
4
Right-Click the screen again, & select ‘Preset’
Enter 95 to access the OSD menu
5
Using mouse, click on area of the screen
labeled:
UP: to scroll up the menu
DOWN: to scroll down the menu
Left: Vertically move from one edit tab
to the one to its left
RIGHT: Vertically move from one
edit tab to the one to its right.
6
Some preset numbers are reserved to special functions.
1
2
To move to a sub-menu
Once you have selected the sub-menu
you want to enter, scroll the mouse’s
wheel forward.
To exit a sub-menu
When you have completed all desired modifications,
scroll the mouse’s wheel forward to save changes,
or backwards to return to the Root menu and cancel
all changes
2
7
PRESET SETUP- UNIDENTIFIED.
PRESET SETUP- DEFINED PRESET
<LABEL>
Edit a label for the selected preset. Max. 10 characters.
CAM ADJUST
- WB and AE can be set up independently for each preset.
-
GENERAL:
WB/ AE settings will follow the camera’s setup for
both options under ‘ROOT MENU>CAMERA SETUP’ menu.
-
SPECIAL:
- Each special WB/AE value will the activated when the
camera runs the selected preset. During jog operation,
general WB/AE value will be applied.
- If ‘SPECIAL’ is selected, any changes made to the general
camera settings for WB and AE will not apply to the
preset’s WB/ AE settings.
ALARM OUT
Relay output can be linked with a specific preset run.
‘ - ‘means off, ‘1’ means on.
If a selected preset is already defined, camera will move to the pre-defined position. If a
selected preset is not defined, ‘UNDEFINED’ will appear.
<EDIT SCENE>
Redefine the current preset scene position(i.e. PTZ).
TO EDIT THE PRESET’S SCENE
1. Using joystick, move camera to the desired position.
2. Using your USB mouse, scroll the mouse’s wheel
forward to save, or backwards to cancel all changes.
Preset #
Function
On/Off