DV Systems K100-C Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 29

background image

K100-C

Dec’15

- 6 -

Shipping Cleats

Your DV Systems ‘K Series’ Rotary Screw Compressor is shipped with several Shipping Cleats that must be
removed prior to the initial start-up. The Shipping Cleats are installed during assembly of the Unit simply to stop
any lateral movement of the Air End, Motor, etc during shipping.

The Cleats are located a) under the (3) Feet of the Oil Receiver, b) (1) under the Air End Bracket, and c) (1) under
the Motor of the Unit. Please remove these after locating the Unit but prior to running.

Oil Receiver / Air End Cleat Removal.

1. Locate the Oil Receiver in the

front right corner of the Unit and
locate the Air End Bracket at the
back of the Unit

2. Locate the orange Shipping Cleat

under each Foot of the Oil
Receiver and one Shipping Cleat
under the Air End Bracket.

3. Remove the Bolt and Washers

from each Cleat, and slide the
Cleat out.

Note: To remove the Cleats, you

may need to apply some
sideways force on the top of
the Receiver.

Motor Cleat Removal.

The Motor is fastened to the Unit framework by means of (1) Shipping Cleat as indicated below. Access to the
Cleat is by means of both the front and rear of the Unit.

Remove the Fasteners and slide the Cleat out of the assembly.

Motor Cleat from Front of Unit.

Motor Cleat from Rear of Unit.

Shipping Cleat

Fasteners

Fasteners

Shipping Cleat

«
...
4
5
6
7
8
...
»

Содержание K100-C






























Отзывы:

Нет отзывов

Похожие инструкции для K100-C

Бренд: Napoleon Страницы: 19

MTA8F128R5I Series

Бренд: Technibel Climatisation Страницы: 47

Бренд: Ultravation Страницы: 4

FreciousCare FCI 5000

Бренд: MANN+HUMMEL Страницы: 11

WISE Parasol Zenith 600

Бренд: Swegon Страницы: 14

Бренд: York Страницы: 4

Бренд: Saivod Страницы: 88

Бренд: Vallox Страницы: 20

Бренд: Kaisai Страницы: 56

Бренд: Rasonic Страницы: 24

Бренд: AERMEC Страницы: 68

Бренд: TECO Страницы: 21

Бренд: SilverOnyx Страницы: 14

Бренд: Midea Страницы: 49

Бренд: Bryant Страницы: 32

Бренд: Daikin Страницы: 228

Бренд: Daikin Страницы: 18

ESAM055-C - 10-04

Бренд: Haier Страницы: 19

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды