background image

For maximum strength and safety, (and 

compliance with SAE Standard J1853) this 

winch should be mounted with three 3/8" or 

M10 bolts, washers, and lock washers.
Select a winch line with breaking strength 

at least 1-1/2 times the winch rating and a 

hook 1-1/2 times stronger than the line. If 

steel cable is selected, the optional reel with 

large hub may extend cable life. (The above 

combination meets SAE Standard J1853 for 

boat trailer winches).
Attach cable or rope by either method 

described in sketch. If nylon strap is used, it 

should have a loop sewn in one end and be 

attached using a 3/8" x 3" long bolt and locknut. Use a locknut, not a nut and 
lock washer. Insert bolt through slots in both reel side plates so that nut is 

on 

gear side. Tighten only until snug with bolt in bottom of slot next to reel 

hub.
To mount the winch, the top cover will need to be removed from the 

winch. To install cable or strap, the top cover and sides will need 

to be removed. See winch cover removal and assembly section for 

instructions.

WINCH MOUNTING AND

CABLE ATTACHMENT

CABLE ATTACHMENT METHODS

(IF CABLE IS USED)

3/8" or M10

Содержание DLx1200













Отзывы: