Dutton-Lainson DLx1200 страница 7 Скачать руководство пользователя

Страница: 7 / 12

The cover comes off the winch in three pieces. To remove the top cover, loosen

and remove the top phillips screws in the front of the cover with a screwdriver.

Pull up on the front of the top cover and rotate the top away from the winch.

Once the locking tabs are disengaged from the sides, pull the cover straight

back to remove.
To remove the cover sides, use a 9/64 hex key to remove the two socket head

screws in the bottom front and back on the winch side. Once the screws are

removed, pull the cover sides away from the winch to remove.
To reassemble the winch cover, slide the two sides into place around the winch.

Use a 9/64 hex key to install the two socket head screws.

CAUTION: Tighten cover screws by hand only. Over-tightening could

make top cover difficult to install or damage winch cover.

With the sides in place and bolts installed, place the tabs on the back of the top

cover around the bolt on the back of the winch. Rotate the top cover back onto

the winch and press on the middle of the top until the locking tabs snap into

the cover sides. Install the phillips screws in the front of the cover and tighten.

WINCH COVER REMOVAL

AND ASSEMBLY

Содержание DLx1200












