DuroStar DS5018CS Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 20

DuroStar DS5018CS Скачать руководство пользователя страница 2

OWNER’S MANUAL

1

△

!

SAFETY FIRST

Instructions contained in warnings within this manual marked with a

△

!

symbol concern critical points which must be taken into consideration to
prevent possible serious bodily injury and for this reason you are
requested to read all such instructions carefully and follow them without
fail.

NOTES ON TYPES OF WARNINGS IN THE MANUAL


This mark indicates instructions which must be followed to prevent accidents
which could lead to serious bodily injury or death.


This mark indicates instructions which must be followed, or it will lead to
mechanical failure, breakdown, or damage.

This mark indicates hints or directions useful in the use of the product.

Contents

1. WARNING LABELS ON THE MACHINE

……………………………… 2

2. SYMBOLS ON THE MACHINE

………………………………………… 3

3. SAFETY PRECAUTIONS

……………………………………………….. 3

4. INSTALLING GUIDE BAR AND SAW CHAIN

………………………… 7

5. FUEL AND CHAIN OIL

…………………………………………………… 8

6. OPERATING ENGINE

…………………………………………………… 10

7. SAWING

…………………………………………………………………… 12

8. MAINTENANCE

………………………………………………………….. 14

9. MAINTENANCE OF SAW CHAIN AND GUIDE BAR

………………… 16

10. TROUBLESHOOTING GUIDE

………………………………………….. 17

11. SPECIFICATIONS

…………………………………………………………18

△

！

WARNING

IMPORTANT

NOTE

«
1
2
3
4
...
»

Содержание DS5018CS





















Отзывы:

Нет отзывов