DuroStar DS5018CS Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 20

DuroStar DS5018CS Скачать руководство пользователя страница 13

OWNER’S MANUAL

12

(1) Switch

7.SAWING



It is not necessary to force the saw into the cut. Apply only light
pressure while running the engine at full throttle.



When the saw chain is caught in the cut, do not attempt to pull it
out by force, but use a wedge or a lever to open the way.

GUARD AGAINST KICKBACK

This saw is equipped with a chain brake that will stop the chain in the event

of kickback if operating properly. You must check the chain break operation
before each usage by running the saw at full the throttle for 1-2 seconds and
pushing the front hand guard forward.

The chain should stop immediately with the

engine at full speed. If the chain is slow to stop or
does not stop, replace the brake band and clutch
drum before use.

It is extremely important that the chain brake be

checked for proper operation before each use and
that the chain be sharp to maintain the kickback
safety leveled the saw. Removal of the safety
devices, inadequate maintenance, or incorrect replacement of the bar or chain
may increase the risk of serious personal injury due to kickback.

FELLING A TREE

a. Decide the felling direction considering the wind, lean of the tree, location of
heavy breaches, ease of job after felling and other factors.
b. Arrange a good foothold and retreat path.
c. Make a notch cut the one-third of the wood into the tree on the felling side.
d. Make a felling cut from the from the opposite side of the notch and at a level
slightly higher than the bottom of the notch.

When you fell a tree, the sure to warn your
neighboring workers of the danger.

(1) Notch cut
(2) Felling cut

△

！

WARNING

△

！

WARNING

«
...
11
12
13
14
15
...
»

Содержание DS5018CS





















Отзывы:

Нет отзывов