DuroStar DS4000S Скачать руководство пользователя страница 11

Страница: 11 / 64

Close choke

The choke lever is located above the air filter to the right

of the recoil start. Slide the lever to the left to cut the air
supply and allow more gas into the engine to start.

Pull recoil start

Open choke

Pull the recoil start handle quickly the complete length of the

rope and then let it retract slowly. The unit will generally start

within 3 pulls.

CAUTION: DO NOT

let go of the handle while

the rope is extended this may cause damage to yourself or

your machine.

The choke lever is located above the air filter to the right

of the recoil start. Slide the lever to the right to open the
choke and increase air into the carburetor for normal
running.

Turn breaker on & connect

devices

Connect your devices to the receptacles on the front panel.

Start with the largest loads first.

10.

Flip engine switch to ON

The engine switch is located on the left side of the front
power panel. Flip the switch to on.

Содержание DS4000S

































































Результаты поиска

Содержание DS4000S

Отзывы:

Похожие инструкции для DS4000S

Бренды по названию

Популярные бренды

DuroStar DS4000S, Руководство пользователя

Результаты поиска

Содержание DS4000S

Отзывы:

Похожие инструкции для DS4000S

Бренды по названию

Популярные бренды