manualshive.com logo in svg

DUROMAX XP7HPX, Руководство пользователя

DUROMAX XP7HPX - мощная насосная станция для водоснабжения и орошения. Теперь вы можете легко найти и скачать бесплатное руководство по эксплуатации на нашем сайте. Получите максимальную эффективность использования этого устройства, загрузив руководство пользователя с manualshive.com.

Поделиться
Скачать
background image

65

65

OWNER’S WARRANTY RESPONSIBILITIES:

As the small off-road engine owner, you are responsible for performance of the required 

maintenance listed in your owner’s manual. DuroMax Power Equipment recommends that you 

retain all receipts covering maintenance on your small off-road engine, but DuroMax Power 

Equipment cannot deny warranty coverage solely for the lack of receipts or your failure to ensure 
the performance of all scheduled maintenance.

As the small off-road engine owner, you should be aware that the DuroMax Power Equipment may
deny you warranty coverage if your small off-road engine or a part has failed due to abuse, neglect, 
or improper maintenance or unapproved modifications.
You are responsible for presenting your small off-road engine to a DuroMax Power Equipment

distribution center or service center as soon as the problem exists. The warranty repairs shall be
completed in a reasonable amount of time, not to exceed 30 days.
If you have any questions regarding your warranty coverage, contact us at 844-387-6629 or email
[email protected].

DEFECTS WARRANTY REQUIREMENTS:

The warranty period begins on the date the engine or equipment is delivered to an ultimate 
purchaser and extends for a period of Two Years.
GENERAL EMISSIONS WARRANTY COVERAGE:
DuroMax Power Equipment warrants to the ultimate purchaser and each subsequent owner that 
the engine or equipment is:
1. Designed, built, and equipped to conform with all applicable regulations adopted by the Air
Resources Board; and
2. Free from defects in materials and workmanship that causes the failure of a warranted part for a
period of two years.
The warranty on emissions-related parts will be interpreted as follows:
1. Any warranted part that is not scheduled for replacement as required maintenance in the
Owner’s Manual must be warranted for the warranty period stated above. If any such part fails 
during the period of warranty coverage, it must be repaired or replaced by DuroMax Power 

Equipment according to Subsection (4) below. Any such part repaired or replaced under the 

warranty must be warranted for a time not less than the remaining warranty period.
2. Any warranted part that is scheduled only for regular inspection in the Owner’s Manual must be
warranted for the warranty period stated above. A statement in such written instructions to the 

effect of “repair or replace as necessary” shall advise owners of the warranty coverage for emission 

related parts. Replacement within the warranty period is covered by the warranty and will not 
reduce the period of warranty coverage. Any such part repaired or replaced under warranty must 
be warranted for a time not less than the remaining warranty period.
3. Any warranted part that is scheduled for replacement as required maintenance in the Owner’s

Manual must be warranted for the period prior to the first scheduled replacement point for that 
part. If the part fails prior to the first scheduled replacement, the part must be repaired or replaced 
by the engine manufacturer according to Subsection (4) below. Any such part repaired or replaced

Содержание XP7HPX







































































Отзывы:

Нет отзывов

Похожие инструкции для XP7HPX

Power Fist 8236275 User Manual preview
8236275
Бренд: Power Fist Страницы: 40
REXROTH GTE Series Project Planning Manual preview
GTE Series
Бренд: REXROTH Страницы: 86
Westerbeke 16BEG Service Manual preview
16BEG
Бренд: Westerbeke Страницы: 110
Perkins 1106D Operation And Maintenance Manual preview
1106D
Бренд: Perkins Страницы: 108
Man E 2942 LE 302 Repair Manual preview
E 2942 LE 302
Бренд: Man Страницы: 18
Grundfos RADIOMODULE 2G4 Installation And Operating Instructions Manual preview
RADIOMODULE 2G4
Бренд: Grundfos Страницы: 76
Bodine 33A Manual preview
33A
Бренд: Bodine Страницы: 8
Briggs & Stratton 09000 Operator'S Manual preview
09000
Бренд: Briggs & Stratton Страницы: 120
STG-BEIKIRCH EM Tandem RWA Technical Information And Operating Instruction preview
EM Tandem RWA
Бренд: STG-BEIKIRCH Страницы: 9
Honda GX 80 Owner'S Manual preview
GX 80
Бренд: Honda Страницы: 48
Honda GCV145 Owner'S Manual preview
GCV145
Бренд: Honda Страницы: 80
Volvo Penta V8-350 Operator'S Manual preview
V8-350
Бренд: Volvo Penta Страницы: 122
Motion CM-40 Manual preview
CM-40
Бренд: Motion Страницы: 92
Motion CM-07 Manual preview
CM-07
Бренд: Motion Страницы: 124
Cors-Air Black Devil Manual preview
Black Devil
Бренд: Cors-Air Страницы: 10
Toyota 3S-GE Repair Manual preview
3S-GE
Бренд: Toyota Страницы: 608
Hobbico AQUACRAFT .18 MARINE Instructions preview
AQUACRAFT .18 MARINE
Бренд: Hobbico Страницы: 4
YARDMAX LC1P65FE-2 Operator'S Manual preview
LC1P65FE-2
Бренд: YARDMAX Страницы: 24

Бренды по названию

Популярные бренды

Загрузить еще бренды