background image

-20

20

40

60

80

0

100 F

-30

-40

-10

0

10 20 30

-20

40 C

30

10W-30

ENVIRONMENTAL TEMPERATURE

5W-30

SAE

WARNING: Gasoline and gas fumes are highly flammable.

 

Do not fill tank near an open flame. 

 

Do not overfill. Always check for fuel spills.

GENERATOR SETUP (CONTINUED)

Add oil

The generator requires engine oil to operate properly. The generator, when new from the package 
contains no oil in the crankcase

*

. You must add the proper amount of oil before operating the 

generator for the first time. This amount is equal to the oil capacity of the engine crankcase:

WARNING:

 

Do not apply engine oils with additives or 2-stroke gasoline engine oils.

 They don’t 

have enough lubrication, and may shorten the engine’s service life.

a. 

Make sure the generator is on a level surface.

b. 

Unscrew the oil filler/dipstick cap from the engine .

c. 

Using a funnel, add the appropriate amount of oil  

 

into the crankcase. You will know the crankcase is  

 

full when the oil level has reached the lower lip of  

 

the opening you have just poured the oil into.

d. 

Replace oil filler cap.

1.

Step 3 - Adding Oil

Engine oil recommended: SAE 10W-30.

 Viscosity varies with 

regions and temperatures. Choose your oil viscosity using the 

chart to the left.

* A small amount of oil from factory testing may be present on 

arrival.

Model Number

XP4850EH

Engine Oil Capacity

20 fl. oz (0.6L)

21

Step 4 - Adding Gasoline

Add Gasoline

a. 

Make sure the generator is on a level surface.

b. 

Unscrew gas cap and set aside (NOTE: the gas cap  

 

may be tight and hard to unscrew).

c. 

Slowly add unleaded gasoline to the fuel tank. Be  

 

careful not to overfill. Please refer to the chart below 

 

 

to find the gas capacity of your generator model. The 

 

 

fuel gauge on the top of the gas tank indicates how  

 

much gasoline is in the generator gas tank.

d. 

Replace fuel cap and wipe up any spilled gasoline  

 

with a dry cloth.

 

NOTE: Gas can expand. Do not fill the gas tank 

 

to the very top. Leave a minimum of 1.5 in of open 

space.

IMPORTANT: 

 

Never use an oil/gasoline mixture. Never use old gas. 

 

Avoid getting dirt or water in the fuel tank. 

 

Gas can age in the tank and make it hard to start up  

 

the generator in the future. 

 

Never store generator for extended periods of time  

 

with fuel in the tank.

2.

To ensure that the generator runs smoothly use only FRESH, UNLEADED GAS WITH AN OCTANE 
RATING OF 87 OR HIGHER.

Model Number

XP4850EH

Gas Tank Capacity

3.96 US Gallons (15L)

20

WARNING: DO NOT overfill the crankcase. This 

may damage the motor and shorting overall life 

of your generator.

Содержание XP4850EH-081418




































Отзывы: