DURKOPP ADLER 911-211 Скачать руководство пользователя страница 39

Страница: 39 / 200

Machine head

Service Instructions 911-211 - 02.0 - 10/2016

4.4.3 Setting the hook side clearance

Order

First, check the following settings:

• A straight and undamaged needle has been inserted (



Operating

Instructions

)

• Needle bar linkage (



p. 33

)

• Loop stroke position (



p. 34

)

Proper setting

Machine locked in place at position

(



p. 28



Maximum 0.1 mm distance between the hook tip and the groove for
the needle.

Cover

• Swivel up the machine head (



p. 15

)

WARNING

Risk of injury from moving parts!

Crushing possible.

Switch off the machine before you check and set
the hook side clearance.

NOTICE

Property damage may occur!

There is a risk of machine damage, needle breakage or damage to
the thread if the distance between needle groove and hook tip is
incorrect.

Check and, if necessary, readjust the distance to the hook tip after
inserting a new needle with a different size.

Содержание 911-211









































































































































































































Результаты поиска

Содержание 911-211

Отзывы:

DURKOPP ADLER 911-211, Инструкция по эксплуатации, Страница: 39 / 200

Результаты поиска

Содержание 911-211

Отзывы: